audi Workshop Repair Guides

Audi Workshop Service and Repair Manuals

Control Assembly, HVAC|Description and Operation|Page 7088 > < Control Assembly, HVAC|Description and Operation
Page 1
background image

Control Assembly: Service and Repair

Climatronic Control Module J255 A/C Control Head, Removing And Installing

-

Climatronic Control Module J255 A/C control head, removing and installing.

NOTE:

-

On vehicles with heating (without A/C system), a Climatronic Control Module J255 heater control head is installed instead of the A/C control
head. There is no Instrument Panel Interior Temperature Sensor G56 and no Interior Temperature Sensor Fan V42 installed in the Climatronic
Control Module J255 heater control head.

-

The Climatronic Control Module J255 A/C (heater) control head can be exchanged in the normal way, component protection is not in effect at this
time. Vehicle Diagnosis, Testing and Information System VAS 5051 in "Guided Fault Finding" function.

-

If a Climatronic Control Module J255 A/C (heater) control head with active component protection (anti-theft system, introduction not yet
finalized) is installed in a different vehicle, only the functions necessary for vehicle safety can be selected, Comfort functions can no longer be
selected. Vehicle Diagnosis, Testing and Information System VAS 5051 in "Guided Fault Finding" function.

-

Component protection (anti-theft system, introduction not yet finalized) can only be cancelled by entering specific vehicle data Vehicle Diagnosis,
Testing and Information System VAS 5051 in "Guided Fault Finding" function.

-

When replacing a Climatronic Control Module J255 A/C (heater) control head, observe exact allocation. Different versions, with or without seat
heating switch, with different temperature unit ( degree C or degree F) on temperature setting rotary switch, rotary switches with black or silver
surface.

-

If a new Climatronic Control Module J255 A/C (heater) control head was installed and basic setting was not performed, A/C system regulation is
limited and this is displayed in the DTC memory as a malfunction. Therefore, perform A/C system basic setting according to specifications after
installing the Climatronic Control Module J255 A/C control head. Vehicle Diagnosis, Testing and Information System VAS 5051 in "Guided Fault
Finding" function.

-

The Climatronic Control Module J255 A/C (heater) control head buttons and rotary switches are lit with light diodes (LEDs, cannot be replaced).

-

The function and indicator lights in the buttons and in the rotary switches cannot be replaced separately.

-

If the Instrument Panel Interior Temperature Sensor G56 measurement is incorrect, check Climatronic Control Module J255 A/C control head
intake grille trim (it must not be closed) and function of the Interior Temperature Sensor Fan V42 Vehicle Diagnosis, Testing and Information
System VAS 5051 in "Guided Fault Finding" function.

-

The selected functions are displayed when the function lights in the various Climatronic Control Module J255 A/C (heater) control head buttons,
rotary switches or display fields light up.

A/C (heater) control head, removing and installing

The Climatronic Control Module J255

Removing

-

Check coding and adaptation of the Climatronic Control Module J255 A/C (heater) control head using the "Replace control module" function in
Guided Fault Finding (if the Climatronic Control Module J255 A/C control head is to be replaced). Vehicle Diagnosis, Testing and Information
System VAS 5051 in "Guided Fault Finding" function.

-

Switch off ignition.

-

Place Hook 3438 - B - on Climatronic Control Module J255 A/C (heater) control head - A - according to illustration (left and right).

-

Carefully pull Climatronic Control Module J255 A/C (heater) control head in - direction of arrow - out of center console.

CAUTION:
-

To prevent damage to the Climatronic Control Module J255 A/C (heater) control head and center console, do not pull too hard.

-

The Climatronic Control Module J255 A/C (heater) control module is held by the clips and brackets in the center console. If clips are
stuck, they must be loosened from behind with a screwdriver.

-

Do not damage surface of center console when removing (cover it if necessary).

Control Assembly, HVAC|Description and Operation|Page 7088 > < Control Assembly, HVAC|Description and Operation