LaCrosse FWD V6-3.0L (2010)
Seat Heater: Description and Operation
Heated/Vented Seat Description and Operation
Heated Seat Components
The heated/vented seat system consists of the following components:
*
Heated seat switch
*
Vented seat switch
*
Radio/HVAC controls
*
Seat memory control module or seat heating control module
*
Seat cushion heating element
*
Seat back heating element
*
Seat cushion temperature sensor
*
Seat cushion blower motor
*
Seat back blower motor
Heated Seat Operation
The driver and passenger heated seats are controlled by separate heated seat switches that are located with the radio/HVAC controls. When a heated seat
switch is pressed, a serial data message is sent from the radio/HVAC controls to the HVAC control module indicating the heated seat command. The
HVAC control module serves as a gateway to transmit the message to the seat memory control module/seat heating control module via serial data line. In
response to this message, the seat memory control module/seat heating control module applies battery voltage through the element supply voltage circuit
of the seat heating elements. The seat memory control module/seat heating control module sends a serial data message back to the HVAC control module
to gateway the information to the radio/HVAC controls to either illuminate or turn off the appropriate temperature indicator.
Temperature Regulation
The seat memory control module monitors the seat temperature through the temperature sensor signal circuit and the temperature sensor (thermistor) that
is located in the seat cushion with the heater element. The temperature sensor is a variable resistor, it's resistance varies as the temperature of the seat
changes. When the temperature sensor resistance indicates to the seat memory control module that the seat has reached the desired temperature, the
module opens the ground path of the seat heating elements through the heated seat element control circuit. The module will then cycle the element
control circuit open and closed in order to maintain the desired temperature.
Vented Seat Operation
The vented seat operation is designed to draw cabin air around and away from the occupant through small holes in the seat cushion and seat back covers,
through channels in the foam pad, and then through the blower motor exhausting the waste air under the seat cushion.
With the ignition in the ON position, the BCM applies battery voltage through the ignition main relay control circuit energizing the ignition main relay.
With the relay energized, battery voltage is applied through the switch side of the relay, a 10 A fuse, and the ignition circuit to the driver and passenger
vented seat blower motors.
The driver and passenger vented seats are controlled by separate vented seat switches located in the with the radio/HVAC controls. When a vented seat
switch is pressed, a serial data message is sent from the radio/HVAC controls to the HVAC control module indicating the vented seat command. The
HVAC control module serves as a gateway to transmit the message to the seat memory control module via the serial data line. In response to this
message, the seat memory control module applies a low side pulse width modulation (PWM) signal through the blower motor control circuits to the seat
cushion and seat back blower motors indicating the vented seat command. The logic in the blower motors then sets the blower speed to the switch set
point. Both blower motors run drawing cabin air around and away from occupant. The seat memory control module then sends a serial data message
back to the HVAC control module to gateway the information back to the radio/HVAC controls to either illuminate or turn off the appropriate switch
indicator.
Remote Start Seat Heating and Ventilation
Some vehicles allow the customer to configure their heated and/or ventilated seats to come on after a remote start is commanded. The heated seats will
only come on if the outside air temperature is below 50°F as measured by the outside air temperature sensor. Seat ventilation will only come on if the
outside air temperature is measured above 80°F. When seat heating is commanded, the heating level will be on the "High" setting. On some vehicles, the
LED display for the heating or ventilation temperature level may not illuminate during remote start operation. When the vehicle operator inserts the key
in the ignition and turns it to the "On" position, the heated seats will automatically turn off. Be aware that during remote start heated seat operation, since
there is no occupant in the seat, the customer may comment that they feel little or no difference in the temperature of the seat. This is due to little heat
transfer to the seat cover occurring since there is no weigh on the cushion. Once the seat is occupied and the seat cover is pressed against the heater
element, heat will begin to transfer more rapidly to the seat cover.
Load Management
