CTS RWD V8-6.2L SC (2009)
Important: Newly programmed transmitters will not function until program mode has been exited (DIC is blank). This must be done
prior to pressing the UNLOCK button in the next step.
10. Press the UNLOCK button on each transmitter that was programmed to finalize the programming and confirm system operation.
Method 2 - Erasing/Adding Transmitters (No Known Transmitter Available)
This procedure will first erase all known transmitters. The procedure will then program a single transmitter or multiple transmitters. Method 2 is a series
of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement transmitter and the vehicle's mechanical
key.
Important: Do not place any known good transmitters within 10 feet of the vehicle when programming with Method 2. If the RCDLR
recognizes a known good transmitter during Method 2 programming, the programming mode will resort to Method 1.
1. The vehicle must be OFF.
2. Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds.
3. The DIC will display a message: PRESS START CONTROL TO LEARN.
4. Press the start control knob.
5. The DIC will display a message: WAIT 10 MINUTES, and then begin to count down from 10 to 0, one minute at a time.
Important: Once the timer has expired, it is necessary to proceed to the next step within 5 minutes. Failure to do so will result in the
exiting of the program mode and the procedure will have to be restarted at step 1.
6. When the counter reaches 0, DIC will display: PRESS START CONTROL TO LEARN.
7. Repeat steps 4-6 two more times, for a total of 30 minutes.
8. At the end of the 30 minute cycle, a beep will occur and the DIC will display: READY FOR ELECTRONIC KEY 1. At this time all previously
known transmitters have been erased.
9. Place the new/replacement transmitter in the console bin pocket with the buttons facing forward. When transmitter 1 is programmed, a beep will be
heard and the DIC will display: READY FOR ELECTRONIC KEY 2.
10. Additional transmitters can be programmed by taking transmitter 2 out of the pocket and inserting transmitter 3. If desired, up to 4 transmitters can
be programmed. Once 4 transmitters have been learned, the DIC will display a message: MAX ELECTRONIC KEYS LEARNED, and
automatically exit the program mode.
11. If learning less than 4 transmitters, press the start control knob to exit the program mode.
Important: Newly programmed transmitters will not function until program mode has been exited (DIC is blank). This must be done
prior to pressing the UNLOCK button in the next step.
12. Press the UNLOCK button on each transmitter that was programmed to finalize the programming and confirm system operation.
Method 3 - Service Programming System Transmitter Programming
This procedure is a 10-minute relearn procedure using the Techline Terminal with SPS software. Once the 10-minute timer has expired, the transmitters
can be programmed to particular positions or all known transmitters can be erased. A scan tool, Techline Terminal, and a replacement transmitter are
required to perform this procedure.
1. Ignition ON, connect a scan tool to the vehicle in the pass-thru arrangement.
2. Insure that all power consuming devices are turned OFF on the vehicle.
3. On the Techline Terminal, select Service Programming System and follow the Techline Terminal on-screen instructions, using the Legacy
Pass-Thru method. Select "VTD Vehicle Theft Deterrent Learn" under Component Replacement. Ensure that "Prepare RCDLR for transmitter
programming" is used.
4. At this point the scan tool must remain connected for the duration of the 10 minute relearn procedure.
5. When the 10 minute relearn procedure has completed, turn the vehicle OFF.
6. With the scan tool still connected, access the following:
*
Vehicle Control Systems
*
Computer/Integrating Systems
*
Module Setup
*
Remote Control Door Lock Receiver
*
Program Key Fobs
7. Select the transmitter position you wish to program:
Important: Selecting Invalidate All transmitters will erase any known transmitters and will cause the DIC to prompt READY FOR
transmitter 1, requiring all transmitters to be relearned to the vehicle.
