Escalade ESV RWD V8-6.2L (2010)
5. Install the axle shaft seal using the J 21128.
6. Drive the tool into the bore until the axle shaft seal bottoms flush with the tube.
7. Install the axle shaft. Refer to Rear Axle Shaft Replacement (See: Transmission and Drivetrain/Drive Axles, Bearings and Joints/Axle Shaft
Assembly/Axle Shaft/Service and Repair).
8. Install the rear axle housing cover. Refer to Rear Axle Housing Cover and Gasket Replacement (8.6, 9.5 Inch Axles) (See: Transmission and
Drivetrain/Differential Assembly/Service and Repair)Rear Axle Housing Cover and Gasket Replacement (10.5 Inch Axle) ().
9. Install the rear wheel speed sensor. Refer to Rear Wheel Speed Sensor Ring Replacement.
10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair).
11. Fill the rear axle. Refer to Differential Oil Replacement (9.5LD Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement)Differential Oil Replacement (8.6 Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement)Differential Oil Replacement (10.5 Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement).
12. Lower the vehicle.
Greater than/Equal to 3900 kg (8600 lb) GVW
Rear Wheel Speed Sensor Ring Replacement
Removal Procedure
Note: The wheel speed sensor ring is integral to the wheel hub and must be replaced as an assembly.
1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle (See: Maintenance/Vehicle Lifting/Service and Repair).
2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair
).
3. Remove the rear brake rotor. Refer to Rear Brake Rotor Replacement (1500 Series) (See: Disc Brake System/Brake Rotor/Disc/Service and
Repair/Removal and Replacement/Rear Brake Rotor Replacement (1500 Series))Rear Brake Rotor Replacement (2500 Series) (See: Disc Brake
System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (2500 Series)).
4. Remove the rear axle hub. Refer to Rear Axle Hub, Bearing, Cup, and/or Seal Replacement (See: Transmission and Drivetrain/Drive Axles,
Bearings and Joints/Axle Bearing/Service and Repair/Rear Axle Hub, Bearing, Cup, and/or Seal Replacement).
Installation Procedure
1. Install the rear axle hub. Refer to Rear Axle Hub, Bearing, Cup, and/or Seal Replacement (See: Transmission and Drivetrain/Drive Axles,
Bearings and Joints/Axle Bearing/Service and Repair/Rear Axle Hub, Bearing, Cup, and/or Seal Replacement).
2. Install the rear brake rotor. Refer to Rear Brake Rotor Replacement (1500 Series) (See: Disc Brake System/Brake Rotor/Disc/Service and
Repair/Removal and Replacement/Rear Brake Rotor Replacement (1500 Series))Rear Brake Rotor Replacement (2500 Series) (See: Disc Brake
System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (2500 Series)).
3. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair).