Equinox AWD V6-3.4L (2008)
Fluid - A/T: Testing and Inspection
6T70/6T75 Transmission Fluid Checking Procedure
Transmission Fluid Check
This procedure checks both the transmission fluid level, as well as the condition of the fluid itself.
Notice: Use Dexron VI transmission fluid only. Failure to use the proper fluid may result in transmission internal damage.
Important: Ensure the transmission has enough fluid in it to safely start the vehicle without damaging the transmission. With the vehicle off
there must be at least enough fluid to wet the end of the dipstick bullet. This will ensure that there is enough fluid in the sump to fill the
components once the vehicle is started.
Level Checking Procedure
1. Park the vehicle on a level surface, apply the parking brake and place the shift lever in PARK (P).
2. Start the engine.
3. Depress the brake pedal and move the shift lever through each gear range, pausing for about 3 seconds in each range. Then move the shift lever
back to PARK (P).
4. Allow the engine to idle 500-800 rpm for at least 1 minute. Release the brake pedal.
5. Keep the engine running and observe the transmission fluid temperature (TFT) using the Driver Information Center or a scan tool.
Important: If the fluid temperature is below the specified range, perform the following procedure to raise the fluid temperature to the
specified range.
6. If the TFT reading is not within the required temperature ranges, allow the vehicle to cool, or operate the vehicle until the appropriate TFT is
reached.
Drive the vehicle in second gear until the fluid temperature is within the specified range.
Important: Check the transmission fluid level when the TFT is between 180°F and 200°F (82°C and 93°C). The fluid level rises as fluid
temperature increases, so it is important to ensure the transmission fluid temperature is within range.
7. Remove the dipstick and wipe it with a clean rag or paper towel.
8. Inspect the fluid color. The fluid should be red or dark brown.
*
If the fluid color is very dark or black and has a burnt odor, inspect the fluid for excessive metal particles or other debris. A small amount of
"friction" material is a "normal" condition. If large pieces and/or metal particles are noted in the fluid, flush the oil cooler and cooler lines and
overhaul the transmission. If there are no signs of transmission internal damage noted, replace the fluid, repair the oil cooler, and flush the
cooler lines.
*
Fluid that is cloudy or milky or appears to be contaminated with water indicates engine coolant or water contamination. Refer to Engine
Coolant/Water in Transmission (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and Inspection/Symptom
Related Diagnostic Procedures/6T70/6T75 - Automatic Transmission/Engine Coolant/Water in Transmission) .
9. Install the dipstick and tighten. Wait three seconds and then remove it again.
Important: Always check the fluid level at least twice. Consistent readings are important to maintaining proper fluid level. If inconsistent
readings are noted, inspect the transmission vent assembly to ensure it is clean and unclogged.
10. Check both sides of the dipstick and read the lower level.
Important: It is not necessary to get the fluid level all the way up to the MAX mark. Anywhere within the crosshatch band is acceptable.
11. Install and remove the dipstick again to verify the reading.
12. If the fluid level is not within the crosshatch band, and the transmission temperature is between 180°F and 200°F (82°C and 93°C), add or dranin
fluid as necessary to bring the level into the crosshatch band. If the fluid level is low, add only enough fluid to bring the level into the crosshatch
band.
Important: Do not add more than one pint (0.5L) at a time without rechecking the level. Once the oil is on the dipstick bullet, it will not
take much more fluid to raise the fluid level into the crosshatch band. Do not overfill. Also, if the fluid level is low, inspect the
transmission for leaks. Refer to Fluid Leak Diagnosis (See: Transmission and Drivetrain/Automatic Transmission/Transaxle/Testing and
Inspection/Component Tests and General Diagnostics/6T70/6T75 - Automatic Transmission/Fluid Leak Diagnosis) .
13. If the fluid level is in the acceptable range, install the dipstick.
14. If the fluid was changed, reset the transmission oil life monitor if applicable.
Fluid Condition Inspection
*
Inspect the fluid color. The fluid should be red in color. The fluid may also turn brown form normal use, and does not always indicate
contamination.
