chevrolet Workshop Repair Guides

Chevrolet Workshop Service and Repair Manuals

Axle Shaft Assembly > < Rear Axle Shaft Seal and/or Bearing Replacement|Page 9464
Page 6
background image

9. Using the J 44420 - installer (2) and the J 8092 - handle (1), install the new oil seal.

10. Install the rotor, if necessary. Refer to Rear Brake Rotor Replacement (JD9)   (See: Brakes and Traction Control/Disc Brake System/Brake

Rotor/Disc/Service and Repair/Rear Brake Rotor Replacement (JD9))Rear Brake Rotor Replacement (JH6)   (See: Brakes and Traction
Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear Brake Rotor Replacement (JH6))Rear Brake Rotor Replacement (JH7)   (
See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear Brake Rotor Replacement (JH7)) .

11. Apply a light coat of high melting point EP bearing lubricant to the axle housing spindle.

Note

If the wheel hub assembly does not fully seat itself onto the axle shaft spindle and is removed, the wheel hub seal must be replaced.

12. Install the wheel hub to the axle housing.

13. Using the J 2222-C - wrench , install the adjusting nut to the hub.
14. Adjust the wheel bearings. Refer to Wheel Bearing Adjustment   (See: Differential Assembly/Service and Repair/Procedures/Rear Drive

Axle/Wheel Bearing Adjustment) .

15. Install the axle shaft. Refer to Rear Axle Shaft and/or Gasket Replacement   (See: Seals and Gaskets/Service and Repair/Rear Axle Shaft and/or

Gasket Replacement) .

16. Install the brake caliper bracket. Refer to Rear Brake Caliper Bracket Replacement (JD9)   (See: Brakes and Traction Control/Disc Brake

System/Brake Caliper/Service and Repair/Removal and Replacement/Rear Brake Caliper Bracket Replacement (JD9))Rear Brake Caliper Bracket
Replacement (JH6, JH7)   (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and
Replacement/Rear Brake Caliper Bracket Replacement (JH6, JH7)) .

17. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation   (See: Maintenance/Wheels and Tires/Service and Repair) .
18. Inspect and add axle lubricant to the axle housing, if necessary. Refer to Rear Axle Lubricant Level Inspection (8.6, 9.5 LD Axle)   (See:

Differential Assembly/Fluid - Differential/Service and Repair/Procedures/Rear Drive Axle/Rear Axle Lubricant Level Inspection (8.6, 9.5 LD
Axle))Rear Axle Lubricant Level Inspection (10.5 Inch Axle)   (See: Differential Assembly/Fluid - Differential/Service and
Repair/Procedures/Rear Drive Axle/Rear Axle Lubricant Level Inspection (10.5 Inch Axle))Rear Axle Lubricant Level Inspection (11.5 Inch
Axle)   (See: Differential Assembly/Fluid - Differential/Service and Repair/Procedures/Rear Drive Axle/Rear Axle Lubricant Level Inspection
(11.5 Inch Axle)) .

19. Lower the vehicle.

Axle Shaft Assembly > < Rear Axle Shaft Seal and/or Bearing Replacement|Page 9464