Silverado 1500 4WD V8-6.2L (2010)
5. Install the axle shaft seal using the J-21128 - Axle Pinion Oil Seal Installer.
6. Drive the tool into the bore until the axle shaft seal bottoms flush with the tube.
7. Install the axle shaft. Refer to Rear Axle Shaft Replacement (See: Transmission and Drivetrain/Drive Axles, Bearings and Joints/Axle Shaft
Assembly/Axle Shaft/Service and Repair).
8. Install the rear axle housing cover. Refer to Rear Axle Housing Cover and Gasket Replacement (8.6, 9.5 Inch Axles) ()Rear Axle Housing Cover
and Gasket Replacement (10.5/11.5 Inch Axle) ().
9. Install the rear wheel speed sensor. Refer to Rear Wheel Speed Sensor Replacement (See: Rear Wheel Speed Sensor Replacement/Non-Hybrid
Less than 3900 kg (8600 lb) GVW).
10. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair).
11. Fill the rear axle. Refer to Differential Oil Replacement (10.5 Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement)Differential Oil Replacement (11.5 Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement)Differential Oil Replacement (8.6 Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement)Differential Oil Replacement (9.5LD Inch Axle) (See: Maintenance/Fluids/Fluid - Differential/Service and
Repair/Removal and Replacement).
12. Lower the vehicle.
Non-Hybrid Greater than/Equal to 3900 kg (8600 lb) GVW
Rear Wheel Speed Sensor Ring Replacement
Removal Procedure
Note: The wheel speed sensor ring is integral to the wheel hub and must be replaced as an assembly.
1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle (See: Maintenance/Vehicle Lifting/Service and Repair).
2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair
).
3. Remove the rear brake rotor. Refer to Rear Brake Rotor Replacement (JD9) (See: Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear
Brake Rotor Replacement (JD9))Rear Brake Rotor Replacement (JH6) (See: Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear
Brake Rotor Replacement (JH6))Rear Brake Rotor Replacement (JH7) (See: Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear
Brake Rotor Replacement (JH7)).
4. Remove the rear axle hub. Refer to Rear Axle Hub, Bearing, Cup, and/or Seal Replacement (See: Transmission and Drivetrain/Drive Axles,
Bearings and Joints/Axle Bearing/Service and Repair/Rear Axle Hub, Bearing, Cup, and/or Seal Replacement).
Installation Procedure
1. Install the rear axle hub. Refer to Rear Axle Hub, Bearing, Cup, and/or Seal Replacement (See: Transmission and Drivetrain/Drive Axles,
Bearings and Joints/Axle Bearing/Service and Repair/Rear Axle Hub, Bearing, Cup, and/or Seal Replacement).
2. Install the rear brake rotor. Refer to Rear Brake Rotor Replacement (JD9) (See: Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear
Brake Rotor Replacement (JD9))Rear Brake Rotor Replacement (JH6) (See: Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear
Brake Rotor Replacement (JH6))Rear Brake Rotor Replacement (JH7) (See: Disc Brake System/Brake Rotor/Disc/Service and Repair/Rear