chevrolet Workshop Repair Guides

Chevrolet Workshop Service and Repair Manuals

Antilock Brake Automated Bleed Procedure|Page 1939 > < Antilock Brake Automated Bleed Procedure|Page 1937
Page 1
background image

Brake Bleeding: Service and Repair
Hydraulic Brake Flushing

Hydraulic Brake System Flushing
Warning:
 Refer to Brake Fluid Irritant Warning   (See: Brakes and Traction Control/Service Precautions/Technician Safety Information/Brake Fluid
Irritant Warning).

Caution:  Refer to Brake Fluid Effects on Paint and Electrical Components Caution   (See: Brakes and Traction Control/Service Precautions/Vehicle
Damage Warnings).

Caution:  When adding fluid to the brake master cylinder reservoir, use only Delco Supreme 11(R), GM P/N 12377967 (Canadian P/N 992667), or
equivalent DOT-3 brake fluid from a clean, sealed brake fluid container. The use of any type of fluid other than the recommended type of brake fluid,
may cause contamination which could result in damage to the internal rubber seals and/or rubber linings of hydraulic brake system components.

1. Inspect the brake fluid for the following conditions, indicating brake fluid contamination:

*

Fluid separation, indicating two types of fluid are present; a substance other than the recommended brake fluid has been introduced into the
brake hydraulic system

-

Swirled appearance - oil-based substance

-

Layered appearance - silicone-based substance

*

Fluid discoloration, indicating the presence of moisture or particles that have been introduced into the brake hydraulic system

-

Cloudy appearance - moisture

-

Dark appearance/suspended particles in fluid - dirt, rust, corrosion, brake dust

2. Inspect the master cylinder reservoir cap diaphragm and the reservoir-to-master cylinder grommets for swelling, indicating brake fluid

contamination.

3. If the brake fluid WAS contaminated with an oil-based or a silicone-based substance, indicated by fluid separation and/or a swollen master

cylinder reservoir cap diaphragm and/or swollen reservoir-to-master cylinder grommets, perform the following:

1. Remove ALL of the following components listed from the vehicle. Each component contains internal rubber seals/linings which have been

contaminated by the contaminated brake fluid in the brake hydraulic system.
Refer to the procedures indicated:

*

Master Cylinder Replacement (Vacuum Assist)   (See: Brakes and Traction Control/Hydraulic System/Brake Master Cylinder/Service and
Repair/Removal and Replacement/Master Cylinder Replacement)Master Cylinder Replacement (Two-Mode Hybrid)   (See: Brakes and
Traction Control/Hydraulic System/Brake Master Cylinder/Service and Repair/Removal and Replacement/Master Cylinder Replacement
)Master Cylinder Replacement (Hydraulic Assist)   (See: Brakes and Traction Control/Hydraulic System/Brake Master Cylinder/Service
and Repair/Removal and Replacement/Master Cylinder Replacement)

*

Front Brake Hose Replacement (JH6, JH7)   (See: Brakes and Traction Control/Hydraulic System/Brake Hose/Line/Service and
Repair/Front Brake Hose Replacement (JH6, JH7))Front Brake Hose Replacement (JD9, JF3, JF7, JG4)   (See: Brakes and Traction
Control/Hydraulic System/Brake Hose/Line/Service and Repair/Front Brake Hose Replacement (JD9, JF3, JF7, JG4))

*

Rear Brake Hose Replacement (To Axle - JF3 without JL4, JF7, JG4)   (See: Brakes and Traction Control/Hydraulic System/Brake
Hose/Line/Service and Repair/Rear Brake Hose Replacement (To Axle - JF3 without JL4, JF7, JG4))Rear Brake Hose Replacement (To
Axle - JD9, JF3 with JL4)   (See: Brakes and Traction Control/Hydraulic System/Brake Hose/Line/Service and Repair/Rear Brake Hose
Replacement (To Axle - JD9, JF3 with JL4))Rear Brake Hose Replacement (Frame to Axle - JH6, JH7)   (See: Brakes and Traction
Control/Hydraulic System/Brake Hose/Line/Service and Repair/Rear Brake Hose Replacement (Frame to Axle - JH6, JH7))Rear Brake
Hose Replacement (To Caliper - JD9)   (See: Brakes and Traction Control/Hydraulic System/Brake Hose/Line/Service and Repair/Rear
Brake Hose Replacement (To Caliper - JD9))Rear Brake Hose Replacement (Caliper - JH6, JH7)   (See: Brakes and Traction
Control/Hydraulic System/Brake Hose/Line/Service and Repair/Rear Brake Hose Replacement (Caliper - JH6, JH7))

*

Front Brake Caliper Replacement (JD9, JF3, JF7, JG4)   (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and
Repair/Removal and Replacement/Front Brake Caliper Replacement (JD9, JF3, JF7, JG4))Front Brake Caliper Replacement (JH6, JH7)   (
See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and Replacement/Front Brake Caliper
Replacement (JH6, JH7))

*

Rear Brake Caliper Replacement (JD9)   (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal
and Replacement/Rear Brake Caliper Replacement (JD9))Rear Brake Caliper Replacement (JH6, JH7)   (See: Brakes and Traction
Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and Replacement/Rear Brake Caliper Replacement (JH6, JH7))

*

Brake Pressure Modulator Valve Replacement   (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Hydraulic
Control Assembly - Antilock Brakes/Service and Repair)

*

Brake Pressure Modulator Valve Replacement   (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Hydraulic
Control Assembly - Antilock Brakes/Service and Repair/Non-Hybrid Less than 3900 kg (8600 lb) GVW)

*

Brake Pressure Modulator Valve Replacement   (See: Brakes and Traction Control/Antilock Brakes / Traction Control Systems/Hydraulic
Control Assembly - Antilock Brakes/Service and Repair/Non-Hybrid Greater than/Equal to 3900 kg (8600 lb) GVW)

Antilock Brake Automated Bleed Procedure|Page 1939 > < Antilock Brake Automated Bleed Procedure|Page 1937