Uplander AWD V6-3.5L VIN 8 (2005)
14. Insert the key into the lock cylinder.
15. Ensure the detent spring (3) and ball (4) are held in place until the cylinder is fully installed. Install the cylinder into the case assembly (11). The
detent ball (4) will line up with the V-shaped groove on the rear of the cylinder.
16. Carefully remove the key, keeping the lock cylinder (9) inserted into the case assembly (11).
17. Insert one shutter spring (8) into each hole located on the front of the cylinder (9).
18. Install the shutter assembly (7) into the recessed area in the front of the cylinder (9). Ensure the ends of the pin on the shutter assembly (7) are
positioned in the pin cavities located on the front face of the cylinder (9).
19. Install the lock cylinder cap (6) by aligning the two notches in the cap with the drain hole located on the bottom of the case assembly (11) and the
corresponding feature on the top of the case assembly (11).Press the cap into place with light hand pressure.
20. Install the appropriate lever (2).
21. Install the retaining ring (12).
22. Snap the appropriate rod retainer (1) into the hole in the lever (2).
ASSEMBLING AND CODING REAR COMPARTMENT LID LOCK
The rear compartment lock cylinder only uses seven of the ten cut positions, 4-10. The tumbler positions alternate in adjacent locations from side to
side with four on one side and three on the other.
1. Hold the cylinder (6) so that the side with four tumbler spring wells faces up.
IMPORTANT: The rear compartment lid lock cylinder tumblers (7) are not self retaining and must be held in place if the key is not fully inserted
into the lock cylinder, or until the cylinder (6) is assembled into the case assembly (1).
2. Insert the tumbler springs (2) into the four spring wells.
3. Insert the tumbler (7) for key cut position 3 into the slot nearest to the front of the lock cylinder (6).
4. Install the three remaining tumblers, key cut positions 6, 8 and 10, on this side of the lock cylinder.
5. Inspect for correct loading of the tumblers (7) by inserting the key into cylinder (6). All of the tumblers should be flush with the outside diameter
of the lock cylinder (6).
6. Turn the cylinder (6) so that the side with three tumbler spring wells faces up.
7. Insert the tumbler springs (7) into the three spring wells.
8. Install the tumbler (7) for key cut position 5 into the slot nearest to the front of the lock cylinder.
9. Install the two remaining tumblers, key cut positions 7 and 9, on this side of the lock cylinder.
10. Inspect for the correct loading of the tumblers (7) by inserting the key into the cylinder (6). All of the tumblers should be flush with the outside
diameter of the lock cylinder (6).
11. Lightly lubricate the tumbler (7) surfaces using the provided lubrication.
12. Install the lock cylinder (6) into case assembly (1).
13. Carefully remove the key, keeping the lock cylinder (6) inserted into the case assembly (1).
14. Insert one shutter spring (5) into each hole located on the front of the cylinder (6).
15. Install the shutter assembly (4) into the recessed area in the front of the cylinder (6). Ensure the ends of the pin on the shutter assembly (4) are
positioned in the pin cavities located on the front face of the cylinder (6).
16. Install the lock cylinder cap (3) by aligning the two notches in the cap with the drain hole located on the bottom of the case assembly (1) and the
corresponding feature on the top of the case assembly (1).Press the cap into place with light hand pressure.
ASSEMBLING AND CODING REAR COMPARTMENT LID RELEASE LOCK CYLINDER
The rear compartment lid release lock cylinder uses four of the ten cut positions 7-10. A retainer tumbler is used in the rear compartment lid release
lock cylinder to retain the lock cylinder in the latch assembly. This retainer tumbler is not moved by the key. The retainer tumbler occupies the slot
closest to the head of the rear compartment lid release lock cylinder and should come already installed in the cylinder.
