Intrepid V6-3.5L VIN K (2003)
Security Lamp/Indicator: Description and Operation
SKIS INDICATOR LAMP
The Sentry Key Immobilizer System (SKIS) uses the Vehicle Theft Security System (VTSS) indicator LED to give an indication when the SKIS is
faulty or when the vehicle has been immobilized due to the use of an invalid ignition key. The LED is controlled by the BCM based upon
messages received from the Sentry Key Immobilizer Module (SKIM). The VTSS/ SKIS indicator LED is hard wired directly to the BCM.
The SKIM sends messages to the BCM to turn the LED on for about three seconds when the ignition switch is turned to the ON position as a bulb
test. After completion of the bulb test, the SKIM sends bus messages to the BCM to keep the LED OFF for a duration of about one second. Then
the SKIM sends messages to the BCM to turn the LED ON or OFF based upon the results of the SKIS self-tests. If the VTSS indicator LED comes
on and stays on after the bulb test, it indicates that the SKIM has detected a system malfunction and/or that the SKIS has become inoperative. If
the SKIM detects an invalid key when the ignition switch is turned to the ON position, it sends messages to the BCM to flash the VTSS indicator
LED.
The SKIM can also send messages to the BCM to flash the LED and to generate a single audible chime tone. These functions serve as an
indication to the customer that the SKIS has been placed in its "Customer Learn" programming mode. See Sentry Key Immobilizer System
Transponder Programming in this section for more information on the "Customer Learn" programming mode.
The VTSS indicator LED is housed in the Automatic Temperature Control (ATC) Sun Sensor located in the instrument panel top cover. Refer to
Group - Instrument Panel and Systems for service of ATC Sun Sensor. If the VTSS indicator LED comes on and stays on after the bulb test
function, diagnosis of the SKIS should be performed with a DRB III scan tool and the proper Body Diagnostic Procedures.
VTSS INDICATOR
The Sentry Key Immobilizer System (SKIS) uses the Vehicle Theft Security System (VTSS) indicator LED to give an indication when the SKIS is
faulty or when the vehicle has been immobilized due to the use of an invalid ignition key The LED is controlled by the BCM based upon messages
received from the Sentry Key Immobilizer Module (SKIM). The VTSS/SKIS indicator LED is hard wired directly to the BCM.
The SKIM sends messages to the BCM to turn the LED on for about three seconds when the ignition switch is turned to the ON position as a bulb
test. After completion of the bulb test, the SKIM sends bus messages to the BCM to keep the LED OFF for a duration of about one second. Then
the SKIM sends messages to the BCM to turn the LED ON or OFF based upon the results of the SKIS self-tests. If the VTSS indicator LED comes
on and stays on after the bulb test, it indicates that the SKIM has detected a system malfunction and/or that the SKIS has become inoperative. If
the SKIM detects an invalid key when the ignition switch is turned to the ON position, it sends messages to the BCM to flash the VTSS indicator
LED.
The SKIM can also send messages to the BCM to flash the LED and to generate a single audible chime tone. These functions serve as an
indication to the customer that the SKIS has been placed in its "Customer Learn" programming mode. See Sentry Key Immobilizer System
Transponder Programming in this section for more information on the "Customer Learn" programming mode.
The VTSS indicator LED is housed in the Automatic Temperature Control (ATC) Sun Sensor located in the instrument panel top cover. Refer to
Instrument Panel and Systems for service of ATC Sun Sensor. If the VTSS indicator LED comes on and stays on after the bulb test function,
diagnosis of the SKIS should be performed with a DRB III scan tool and the proper Body Diagnostic Procedures.
