Journey FWD V6-3.5L (2009)
entry unlock button. When Driver Door 1st Press is selected, you must press of the remote keyless entry unlock button twice to unlock the
passenger's doors. When ALL DOORS 1ST PRESS is selected, all of the doors will unlock on the first press of the remote keyless entry unlock
button. To make your selection, press and release the RESET button until "Driver Door 1st Press" or "All Doors 1st Press" appears.
-
Sound Horn with Remote Key Lock When ON is selected, a short horn sound will occur when the remote keyless entry "Lock" button is
pressed. This feature may be selected with or without the flash lights on lock/unlock feature. To make your selection, press and release the RESET
button until "ON" or "OFF" appears.
-
Flash Lights with Remote Key Lock When ON is selected, the front and rear turn signals will flash when the doors are locked or unlocked with
the remote keyless entry transmitter. This feature may be selected with or without the sound horn on lock feature selected. To make your selection,
press and release the RESET button until "ON" or "OFF" appears.
-
Delay Turning Headlights Off When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds
when exiting the vehicle. To make your selection, press and release the RESET button until "0," "30," "60," or "90" appears.
-
Headlights On with Wipers (Available with Auto Headlights Only) When this feature is selected and the headlight switch is in the AUTO
position, the headlights will activate approximately 10 seconds after the wipers are turned on. To make your selection, press and release the
RESET button until "ON" or "OFF" appears.
-
Delay Power Off to Accessories Until Exit When this feature is selected, the power window switches, radio, hands-free system (if equipped),
DVD video system (if equipped), power sunroof (if equipped), and power outlets will remain active for up to 10 minutes after the ignition switch
is turned off. Opening a vehicle door will cancel this feature. To make your selection, press and release the RESET button until "Off," "45 sec.,"
"5 min.," or "10 min." appears.
-
Confirmation of Voice Commands - If Equipped When ON is selected, all voice commands from the UConnect(TM) system are confirmed. To
make your selection, press and release the RESET button until "ON" or "OFF" appears.
-
Display Units of Measure in The EVIC, odometer, and navigation system (if equipped) can be changed between English and Metric units of
measure. To make your selection, press and release the RESET button until "US" or "METRIC" appears.
COMPASS/TEMPERATURE
Compass heading and outside temperature are displayed on the EVIC display screen. One of eight compass headings to indicate the direction the vehicle
is facing (N, S, E, W, NE, NW, SE, SW) and one of 15 compass variance settings can be programmed. Outside temperature is displayed in °C (degrees
Celsius) or °F (degrees Fahrenheit).
For additional information regarding the compass, refer to Personal Settings (Customer Programmable Features).
TRIP COMPUTER
Press and release the MENU button until one of the following Trip Functions displays in the EVIC:
-
Average Fuel Economy
-
Distance To Empty
-
Elapsed Time
-
Display Units of Measure in
Press the STEP button to cycle through all the Trip Computer functions.
The Trip Functions mode displays the following information:
-
Average Fuel Economy Shows the average fuel economy since the last reset. When the fuel economy is reset, the display will read "RESET" or
show dashes for two seconds. Then, the history information will be erased, and the averaging will continue from the last fuel average reading
before the reset.
-
Distance To Empty (DTE) Shows the estimated distance that can be traveled with the fuel remaining in the tank. This estimated distance is
determined by a weighted average of the instantaneous and average fuel economy, according to the current fuel tank level. DTE cannot be reset
through the RESET button. When the DTE value is less than 30 miles (48 km) estimated driving distance, the DTE display will change to a text
display of "LOW FUEL." This display will continue until the vehicle runs out of fuel. Adding a significant amount of fuel to the vehicle will turn
off the "LOW FUEL" text and a new DTE value will display.
-
Elapsed Time Shows the total elapsed time of travel since the last reset when the ignition switch is in the ACC position. Elapsed time will
increment when the ignition switch is in the ON or START position.
-
Display Units of Measure in: To make your selection, press and release the RESET button until "US" or "METRIC" appears.
To Reset The Display Reset will only occur while a resettable function is being displayed. Press and release the RESET button once to clear the
resettable function being displayed. To reset all resettable functions, press and release the RESET button a second time within 3 seconds of resetting the
currently displayed function (>Reset ALL will display during this 3 second window).
