RAM 2500 Truck 4WD V8-5.9L VIN Z LDC (1998)
Rotating the key actuator switch 45 degrees clockwise, remove the key completely from the switch and verify that the switch actuator hole stays in the
new position (45 degrees clockwise from horizontal). The switch is spring loaded to the "on" position. It will return to the "on" position unless you
remove the key. When the IGNITION is ON, this procedure will illuminate the OFF@ light indicator on the passenger airbag disable switch.
To re-enable the passenger side airbag, reverse the procedure above so that the key switch actuator is returned to a horizontal position.
NOTE: Do not turn ignition on with key in switch.
Do not turn switch with ignition on.
Do not leave key in switch.
Do not leave the key in the key actuator under any condition.
Airbag Diagnostic Trouble Codes
Airbag Diagnostic Trouble Codes
Airbag diagnostic trouble codes consist of active and stored codes. If more than one code exists, diagnostic priority should be given to the active codes.
Each diagnostic trouble code is diagnosed by following a specific testing procedure. The diagnostic test procedures contain step-by-step instructions for
determining the cause of the trouble codes. It is not necessary to perform all of the tests in this book to diagnose an individual code.
Always begin by reading the diagnostic trouble codes using the DRB. The procedure begins with AIRBAG TEST 1A - Identifying Airbag System
Problems. This will direct you to the specific test(s) that must be performed.
Active diagnostic trouble codes for the airbag system are not permanent and will change the moment the reason for the code is corrected. In certain test
procedures within this manual, diagnostic trouble codes are used as a diagnostic tool.
Active Codes
The code becomes active as soon as the malfunction is detected or key-off, whichever occurs first. An active trouble code indicates an on-going
malfunction. This means that the defect is currently there every time the airbag control module checks that circuit/function. It is impossible to erase an
active code; active codes automatically erase by themselves when the reason for the code has been corrected.
With the exception of the warning lamp trouble codes or malfunctions, when a malfunction is detected, the airbag lamp remains lit for a minimum of 12
seconds or as long as the malfunction is present.
The seat belt lamp replaces the airbag lamp if the airbag lamp is defective. The seat belt lamp pulses on and off 30 times if the airbag warning lamp is
defective.
Stored Codes
Airbag codes are automatically stored in the ACM's memory as soon as the malfunction is detected. The exception is the" Loss of Ignition Run Only"
code which is an active code only.
A "stored" code indicates there was an active code present at some time. However, the code currently may not be present as an active code, although
another active code could be.
When a trouble code occurs, the airbag warning lamp illuminates for 12 seconds minimum (even if the problem existed for less than 12 seconds). The
code is stored, along with the time in minutes it was active, and the number of times the ignition has been cycled since the problem was last detected.
The minimum time shown for any code will be one minute, even if the code was actually present for less than one minute. Thus, the time shown for a
code that was present for two minutes 13 seconds, for example, would be three minutes.
If a malfunction is detected a diagnostic trouble code is stored and will remain stored as long as the malfunction exists. When and if the malfunction
ceases to exist, an ignition cycle count will be initiated for that code. If the ignition cycle count reaches 100 without a reoccurrence of the same
malfunction, the diagnostic trouble code is erased and that ignition cycle counter is reset to zero. If the malfunction reoccurs before the count reaches
100, then the ignition cycle counter will be reset and the diagnostic trouble code will continue to be a stored code.
If a malfunction is not active while performing a diagnostic test procedure, the active code diagnostic test will not locate the source of the problem. In
this case, the stored code can indicate an area to inspect.
If no obvious problems are found, erase stored codes, and with the ignition "on" wiggle the wire harness and connectors, rotate the steering wheel from
stop to stop. Recheck for codes periodically as you work through the system. This procedure may uncover a malfunction that is difficult to locate.
Airbag Trouble Codes
