Talon AWD L4-1997cc 2.0L DOHC Turbo (1991)
f.
Connect release switch harness connector, then disconnect control unit harness connector.
g. Connect ohmmeter between control unit connector terminal 5 and ground.
h. Observe ohmmeter while moving slide anchor.
i.
Ohmmeter should indicate continuity when slide anchor is not in release (switch ON) range.
j.
Ohmmeter should indicate infinite ohms when slide anchor is in release (switch OFF) range.
k. If resistance is as specified, proceed to step 2.
l.
If resistance is not as specified, repair harness or replace motor and track assembly as necessary.
2.
Check buckle switch circuit as follows:
a. Disconnect buckle switch harness connector.
b. Connect a suitable ohmmeter between buckle switch connector terminal 2 and ground.
c. Ohmmeter should indicate continuity.
d. If continuity is indicated, proceed to step f.
e. If continuity is not indicated, repair harness as necessary.
f.
Connect buckle switch harness connector, then disconnect control unit harness connector. Ensure lap belt is unfastened (buckle switch ON).
g. Connect ohmmeter between control unit connector terminal 2 and ground.
h. Ohmmeter should indicate continuity.
i.
If continuity is indicated, proceed to step 3.
j.
If continuity is not indicated, repair harness or replace buckle as necessary.
3.
Check outer switch circuit as follows:
a. Disconnect outer switch harness connector.
b. Connect ohmmeter between outer switch connector (harness side) terminal 1 and ground, then terminal 3 and ground.
c. Ohmmeter should indicate continuity in both circuits.
d. If continuity is indicated, proceed to step f.
e. If continuity is not indicated, repair harness as necessary.
f.
Connect ohmmeter between outer switch connector (switch side) terminals 1 and 2 (left side), then between terminals 3 and 4 (right side).
g. Observe ohmmeter while pulling out and retracting shoulder belt.
h. With shoulder belt fully retracted to pulled out approximately half way (outer switch Off), infinite resistance should be indicated.
i.
With shoulder belt pulled half way out to fully out position (outer switch On), continuity should be indicated.
j.
If resistance is as specified, proceed to step l.
k. If resistance is not as specified, replace shoulder belt retractor assembly.
l.
Connect shoulder belt to slide anchor (outer switch ON). Connect outer switch harness connector, then disconnect control unit harness
connector.
m. Connect ohmmeter between control unit connector terminal 3 and ground, then terminal 14 and ground.
n. Ohmmeter should indicate continuity in both circuits.
o. If continuity is indicated, circuit is satisfactory.
p. If continuity is not indicated, repair harness as necessary.
Driver's Side
NOTE: Refer to SCHEMATIC DIAGRAMS/ELECTRICAL AND ELECTRONIC DIAGRAMS when performing these tests.
1.
Disconnect door latch switch harness connector.
2.
Connect a suitable ohmmeter between door latch switch terminals 1 and 3, then terminals 2 and 3.
3.
Observe ohmmeter while opening and closing door.
4.
Infinite ohms should be indicated between terminals 1 and 3 when door is open, continuity should be indicated between terminals 1 and 3 when
door is closed.
5.
Continuity should be indicated between terminals 2 and 3 when door is open, infinite ohms should be indicated between terminals 2 and 3 when
door is closed.
6.
If resistance indicated is as specified, circuit is satisfactory. Proceed to step 8.
7.
If resistance indicated is not as specified, replace door latch switch.
8.
Connect ohmmeter between door latch switch connector terminal 3 and ground.
9.
Ohmmeter should indicate continuity.
10.
If continuity is indicated, circuit is satisfactory. Proceed to step 12.
11.
If continuity is not indicated, repair harness as necessary.
12.
Connect door latch switch harness connector, then disconnect control unit harness connector.
13.
Connect ohmmeter between control unit connector terminal 6 and ground.
14.
Observe ohmmeter while opening and closing door.
15.
Continuity should be indicated when door is open, infinite ohms should be indicated is closed.
16.
If resistance indicated is as specified, circuit is satisfactory. Proceed to step 18.
17.
If resistance indicated is not as specified, repair harness as necessary.
18.
Disconnect fasten switch harness connector.
19.
Connect ohmmeter between fasten switch connector terminal 6 and ground.
20.
Observe ohmmeter while opening and closing door.
21.
Infinite ohms should be indicated when door is open, continuity should be indicated when door is closed.
22.
If resistance indicated is as specified, circuit is satisfactory. Proceed to step 24.
23.
If resistance indicated is not as specified, repair harness as necessary.
