Escape 4WD V6-181 3.0L DOHC VIN 1 Duratec (2003)
There are two deactivation procedures.
^
One procedure requires removal of the front seats. This procedure will be used when diagnosing or repairing a seat side air bag concern. This
procedure will also be used when diagnosing or repairing any in-seat or seat-mounted component of a seat equipped with a seat side air bag. The
seat must be removed when performing repairs on a seat equipped with a seat side air bag.
^
The other procedure does not require front seat removal during the diagnostic and repair process. This procedure will be used when diagnosing or
repairing a concern that is not related to a seat equipped with a seat side air bag.
WARNING: IF THE SUPPLEMENTAL RESTRAINT SYSTEM (SRS) IS BEING SERVICED, THE SYSTEM MUST BE DEACTIVATED
AND RESTRAINT SYSTEM DIAGNOSTIC TOOLS MUST BE INSTALLED.
THE AIR BAG RESTRAINT SYSTEM DIAGNOSTIC TOOLS MUST BE REMOVED AND THE AIR BAG MODULES RECONNECTED
WHEN THE SYSTEM IS REACTIVATED TO AVOID NON-DEPLOYMENT IN A COLLISION, RESULTING IN POSSIBLE PERSONAL
INJURY.
NOTE:
^
Diagnostics or repairs are not to be performed on a seat equipped with a seat side air bag with the seat in the vehicle. Prior to attempting to
diagnose or repair a seat concern when equipped with a seat side air bag, the seat must be removed from the vehicle and the restraint system
diagnostic tools must be installed in the seat side air bag electrical connectors. The restraint system diagnostic tools must be removed prior to
operating the vehicle over the road.
^
After diagnosing or repairing an SRS, the restraint system diagnostic tools must be removed before operating the vehicle over the road.
^
After diagnosing or repairing a seat system, the restraint system diagnostic tools must be removed before operating the vehicle over the road.
^
The SRS must be fully operational and free of faults before releasing the vehicle to the customer.
1. Move and tilt the front seats to their highest and most forward position.
2. Disconnect the battery ground cable.
WARNING: TO AVOID ACCIDENTAL DEPLOYMENT AND POSSIBLE PERSONAL INJURY, THE BACKUP POWER SUPPLY
MUST BE DEPLETED BEFORE REPAIRING OR REPLACING ANY FRONT OR SIDE AIR BAG SUPPLEMENTAL RESTRAINT
SYSTEM (SRS) COMPONENTS AND BEFORE SERVICING, REPLACING ADJUSTING OR STRIKING COMPONENTS NEAR
THE FRONT OR SIDE AIR BAG SENSORS, SUCH AS DOORS, INSTRUMENT PANEL, CONSOLE, DOOR LATCHES, STRIKERS,
SEATS AND HOOD LATCHES.
THE SIDE AIR BAG SENSORS ARE LOCATED AT OR NEAR THE BASE OF THE B-PILLAR.
TO DEPLETE THE BACKUP POWER SUPPLY ENERGY, DISCONNECT THE BATTERY GROUND CABLE AND WAIT AT
LEAST ONE MINUTE. BE SURE TO DISCONNECT AUXILIARY BATTERIES AND POWER SUPPLIES (IF EQUIPPED).
3. Wait at least one minute for the backup power supply in the Restraints Control Module (RCM) to deplete its stored energy.
4. Access the driver air bag module electrical connector to the clockspring behind the access panel in the bottom of the steering wheel.
5. Disconnect the driver air bag module electrical connector to the clockspring.
6. Attach a restraint system diagnostic tool 418-F468 to the clockspring side of the driver air bag module electrical connector.
7. Disconnect the passenger air bag module electrical connector.
8. Attach a restraint system diagnostic tool 418-F468 to the harness side of the passenger air bag module electrical connector.
9. If equipped with side air bags, disconnect the passenger side air bag module electrical connector beneath the front seat.
10. Attach a restraint system diagnostic tool 418-F470 to the passenger side air bag electrical connector beneath the passenger seat.
11. Attach a restraint system diagnostic tool 418-F468 to the passenger safety belt buckle electrical connector.
12. If equipped with side air bags, disconnect the driver side air bag module electrical connector beneath the driver seat.
13. Attach a restraint system diagnostic tool 418-F470 to the driver side air bag module electrical connector beneath the front seat.
14. Attach a restraint system diagnostic tool 418-F468 to the driver safety belt buckle electrical connector.
15. Reconnect the battery ground cable.
Seats Removed
There are two reactivation procedures.
^
One procedure requires removal of the front seats. This procedure will be used when diagnosing or repairing a seat side air bag concern. This
procedure will also be used when diagnosing or repairing any in-seat or seat-mounted component of a seat equipped with a seat side air bag. The
seat must be removed when performing repairs on a seat equipped with a seat side air bag.
^
The other procedure does not require front seat removal during the diagnostic and repair process. This procedure will be used when diagnosing or
repairing a concern that is not related to a seat equipped with a seat side air bag.
1. Disconnect the battery ground cable.
WARNING: THE AIR BAG RESTRAINT SYSTEM DIAGNOSTIC TOOLS MUST BE REMOVED AND THE AIR BAG MODULES
RECONNECTED WHEN THE SYSTEM IS REACTIVATED TO AVOID NON-DEPLOYMENT IN A COLLISION, RESULTING IN
POSSIBLE PERSONAL INJURY.
