Explorer 2WD V8-4.6L VIN 8 (2006)
Keyless Entry Key-Pad: Service and Repair
Autolock and Horn Chirp Programming
AUTOLOCK AND HORN CHIRP PROGRAMMING
Auto-Lock Programming Using the Remote Keyless Entry (RKE) Keypad
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. Enter the 5-digit permanent entry code into the RKE keypad.
4. Within 5 seconds of entering the code, press and hold the 3/4 button on the RKE keypad.
5. Within 5 seconds of Step 3, and while holding the 3/4 button, press the 7/8 button on the RKE keypad and release it.
6. NOTE: If the autolock is disabled, the horn chirps once. If the autolock feature is enabled, the horn chirps once shortly and then sounds a second
time with a longer sound of the horn once the above sequence is completed.
Within 5 seconds of Step 3, release the 3/4 button on the RKE keypad.
Auto-Lock Programming Using the Ignition Lock Cylinder
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. NOTE: Steps 5 through 9 must be carried out within 30 seconds.
Turn the ignition key from OFF to RUN.
4. Press the door lock control switch UNLOCK button 3 times.
5. Turn the ignition key from RUN to OFF.
6. Press the door lock control switch UNLOCK button 3 times.
7. Turn the ignition key from OFF to RUN.
8. Verify the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.
9. Press the door lock control switch UNLOCK button then the LOCK button 1 time to command the module to toggle the autolock/relock feature.
10. Verify that the horn chirps. There should be 1 chirp indicating that autolock/relock feature has been disabled. If 1 chirp is heard, followed by a
longer sound of the horn, the autolock/relock feature has just been enabled.
11. Turn the key to the OFF position or wait 2 minutes to exit the enable/disable mode.
12. Verify that the horn chirps once to indicate that a feature has been changed and that autolock/relock has been toggled.
Auto-Unlock Programming Using the Remote Keyless Entry (RKE) Keypad
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. Enter the 5-digit permanent entry code into the RKE keypad.
4. Within 5 seconds of entering the code, press and hold the 3/4 button on the RKE keypad.
5. Within 5 seconds of Step 3, and while holding the 3/4 button, press the 7/8 button twice on the RKE keypad and release it.
6. NOTE: If the auto-unlock is disabled, the horn chirps once. If the auto-unlock feature is enabled, the horn chirps twice.
Within 5 seconds of Step 3, release the 3/4 button on the RKE keypad.
Auto-Unlock Programming Using the Ignition Lock Cylinder
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. NOTE: Steps 5 through 9 must be carried out within 30 seconds.
Turn the ignition key from OFF to RUN.
4. Press the door lock control switch UNLOCK button 3 times.
5. Turn the ignition key from RUN to OFF.
6. Press the door lock control switch UNLOCK button 3 times.
7. Turn the ignition key from OFF to RUN.
8. Verify the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.
9. Press the door lock control switch LOCK button then the UNLOCK button 1 time to command the module to toggle the auto-unlock feature.
10. Verify that the horn chirps. There should be 1 chirp indicating that auto-unlock feature has been disabled. If 1 chirp is heard, followed by a longer
sound of the horn, the auto-unlock feature has just been enabled.
11. Turn the key to the OFF position or wait 2 minutes to exit the enable/disable mode.
12. Verify that the horn chirps once to indicate that a feature has been changed and that auto-unlock has been toggled.
