Explorer AWD V8-4.6L (2010)
NOTE: This procedure is for rolling code devices. In order to determine if you have a fixed code or a rolling code device, open the garage door opener
transmitter and if there is a panel of coded dip switches present, the device is a fixed code device. If there are no coded dip switches present, the device
is a rolling code device.
1. Turn the ignition to the ON position.
2. At the same time, firmly press the 2 outside Lear Car2U(R) System buttons for 1-2 seconds, then release the buttons.
3. NOTE: Step 4 must be initiated within 30 seconds of pressing and releasing the "learn" or "smart" button.
At the garage door opener receiver (the motor-head unit) in the garage, locate the "learn" or "smart" button. This can usually be found near where
the hanging antenna wire is attached to the motor-head unit; or it may be under the light bulb cover of the motor-head unit.
-
For technical assistance, refer to the Owner's Literature.
4. Return to the vehicle and firmly press and hold for 5-20 seconds the universal transmitter button that is desired to be programmed. During this
time, the selected button red indicator light blinks slowly. Once the garage door begins to move, within one second, release the button. With the
button released, the red indicator light begins to blink rapidly until programming is complete. Repeat the press/hold/release sequence a second
time and depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete
the programming process.
5. After successful programming, the Lear Car2U(R) System operates the garage door opener using the button that was programmed. The red
indicator light in front of the programmed button illuminates to confirm the Lear Car2U(R) System is responding (and is programmed) to the
button command.
Erasing the Lear Car2U(R) System Buttons (Rolling Code) - Late Build
1. To erase the rolling code programming from the Lear Car2U(R) System, turn the ignition key to the on position, firmly press and hold the 2
outside Lear Car2U(R) System buttons at the same time for approximately 20 seconds until the 3 red indicator lights begin to blink rapidly.
2. When the 3 red indicator lights begin to blink, release the buttons. The codes for all of the 3 buttons are erased.
Universal Transmitter Programming (Fixed Code) - Late Build (Lear Car2U(R))
WARNING: To avoid the risk of serious injury from the door closing, make sure that people and objects are clear of the garage door opener or
security device that is being programmed. When programming a garage door, it is advised to park outside of the garage.
NOTE: Do not use the Lear Car2U(R) System with any garage door opener that does not have a "stop and reverse" feature. This includes any garage
door opener model manufactured before April 1, 1982.
NOTE: Read the instructions completely before attempting to program the Lear Car2U(R) System. Because of the steps involved, it may be helpful to
have an assistant when programming the universal transmitter.
NOTE: Make sure to keep the original remote control transmitter for use in other vehicles as well as for future Lear Car2U(R) System programming. It
is only needed for fixed code device programming.
NOTE: This procedure is for fixed code devices. In order to determine if you have a fixed code or a rolling code device, open the garage door opener
transmitter and if there is a panel of coded dip switches present, the device is a fixed code device. If there are no coded dip switches present, the device
is a rolling code device. If so, refer to the Training a Garage Door Opener Equipped With "Rolling Codes" - Late Build procedure.
NOTE: In order to program a fixed code device, paper and a pen or pencil is necessary.
1. NOTE: When a switch is in the Up, +, or On position, circle "Left". When a switch is in the Middle, 0 or Neutral position, circle "Middle". When
a switch is in the Down, -, or Off position, circle "Right".
Open the battery cover of the universal transmitter and record the dip switch settings from left to right for all 8 to 12 switches. For additional
information, refer to Specifications.
2. Turn the ignition to the ON position.
3. To input these positions into the Lear Car2U(R) System, at the same time, press all 3 Lear Car2U(R) System buttons for a few seconds and then
release to put the device into the programming mode. The 3 red indicator lights blink slowly. Within 2.5 minutes, enter the corresponding dip
switch settings from left to right (starting with number 1) into the Lear Car2U(R) System by pressing and releasing the buttons corresponding to
the settings you circled.
-
For example, if the dip switch settings were 1 (Left), 2 (Middle), 3 (Middle), 4 (Right), etc., press and release the left Lear Car2U(R) System
button, then the middle button, then the middle button, then the right button, etc.