Explorer Sport Trac 2WD V8-4.6L (2008)
Keyless Entry Transmitter: Testing and Inspection
Autolock and Horn Chirp Programming
AUTOLOCK AND HORN CHIRP PROGRAMMING
Autolock Programming Using the Keyless Entry Keypad
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. Enter the 5-digit permanent entry code into the keyless entry keypad.
4. Within 5 seconds of entering the code, press and hold the 3/4 button on the keyless entry keypad.
5. Within 5 seconds of Step 3, and while holding the 3/4 button, press the 7/8 button on the keyless entry keypad and release it.
6. NOTE: If the autolock is disabled, the horn chirps once. If the autolock feature is enabled, the horn chirps once shortly and then sounds a second
time with a longer sound of the horn once the above sequence is completed.
Within 5 seconds of Step 3, release the 3/4 button on the keyless entry keypad.
Autolock Programming Using the Ignition Lock Cylinder
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. NOTE: Steps 5 through 9 must be carried out within 30 seconds.
Turn the ignition key from OFF to RUN.
4. Press the door lock control switch UNLOCK button 3 times.
5. Turn the ignition key from RUN to OFF.
6. Press the door lock control switch UNLOCK button 3 times.
7. Turn the ignition key from OFF to RUN.
8. Verify the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.
9. Press the door lock control switch UNLOCK button then the LOCK button 1 time to command the module to toggle the autolock/relock feature.
10. Verify that the horn chirps. There should be 1 chirp indicating that autolock/relock feature has been disabled. If 1 chirp is heard, followed by a
longer sound of the horn, the autolock/relock feature has just been enabled.
11. Turn the key to the OFF position or wait 2 minutes to exit the enable/disable mode.
12. Verify that the horn chirps once to indicate that a feature has been changed and that autolock/relock has been toggled.
Auto-Unlock Programming Using the Keyless Entry Keypad
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. Enter the 5-digit permanent entry code into the keyless entry keypad.
4. Within 5 seconds of entering the code, press and hold the 3/4 button on the keyless entry keypad.
5. Within 5 seconds of Step 3, and while holding the 3/4 button, press the 7/8 button twice on the keyless entry keypad and release it.
6. NOTE: If the auto-unlock is disabled, the horn chirps once. If the auto-unlock feature is enabled, the horn chirps twice.
Within 5 seconds of Step 3, release the 3/4 button on the keyless entry keypad.
Auto-Unlock Programming Using the Ignition Lock Cylinder
1. Close all doors and windows.
2. Confirm that the ignition key is OFF.
3. NOTE: Steps 5 through 9 must be carried out within 30 seconds.
Turn the ignition key from OFF to RUN.
4. Press the door lock control switch UNLOCK button 3 times.
5. Turn the ignition key from RUN to OFF.
6. Press the door lock control switch UNLOCK button 3 times.
7. Turn the ignition key from OFF to RUN.
8. Verify the horn chirps. This indicates the enable/disable mode and now is ready to accept program changes.
9. Press the door lock control switch LOCK button then the UNLOCK button 1 time to command the module to toggle the auto-unlock feature.
10. Verify that the horn chirps. There should be 1 chirp indicating that auto-unlock feature has been disabled. If 1 chirp is heard, followed by a longer
sound of the horn, the auto-unlock feature has just been enabled.
11. Turn the key to the OFF position or wait 2 minutes to exit the enable/disable mode.
12. Verify that the horn chirps once to indicate that a feature has been changed and that auto-unlock has been toggled.
