| Description and Operation Section 100-04: Noise, Vibration and Harshness | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-F027 | Vibration Analyzer | - | Commercially available | | 107-R2100 | EngineEAR | - | Commercially available | | 107-R2102 | ChassisEAR | - | Commercially available | | 134-R0135 | Ultrasonic Leak Detector | - | Leitenberger ULG01 or equivalent | Section 204-01: Front Suspension | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 205-014 | Pinion Bearing Cup Replacer | 205-066 (15-033) | Installer, Differential Bearing Cone | | 205-153 | Handle | - | Not required | | 205-D002 | Pinion Bearing Cone Remover | - | Commercially available | | 205-D015 | Step Plate | - | Commercially available | | 205-D069 | Front Hub Replacer | - | Commercially available | | 205-D070 | Front Hub Remover | - | Commercially available | | 211-105 | Tie Rod End Remover | - | Commercially available | Section 204-02: Rear Suspension | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-001 | Impact Slide Hammer | 205-047 (15-011) | Slide Hammer | | 204-019 | Seal Replacer | 204-160 (14-040) | Installer, Front Wheel Bearing | | 204-020 | Bearing Cup Replacer | 205-066-01 (15-033-01) | Adaptor for 205-066 (15-033) | | 204-161 | Installer, Half Shaft | 204-161 (14-041) | Installer, Halfshaft | | 205-014 | Pinion Bearing Cup Replacer | 205-073 (15-034) | Installer, Differential Bearing Cone | | | | 205-074 (15-035) | Installer, Differential Bearing Cone | | | | 205-066-04 (15-068) | Adapter for 205-066 (15-033) | | 205-098 | Rear Axle Draw Bar | 205-066 (15-033) | Installer, Differential Bearing Cone | | 205-153 | Handle | - | Not required | | 205-224 | Axle Bearing Remover | - | Commercially available (Schrem) | | 205-D002 | Pinion Bearing Cone Remover | 205-310 (15-091) | Remover, Bearing/Gear | | 205-D015 | Wheel Bearing Adapter | - | Commercially available | | 205-D070 | Front Hub Remover | - | Commercially available | | 308-153 | Differential Bearing Cup Replacer | 308-046 (16-016) | Installer, Extension Housing Bushing/Oil Seal | Section 204-04: Wheels and Tires | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 418-F123 | Radial Runout Gauge | - | Commercially available | Section 205-00: Driveline System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-002 | Dial Indicator with Bracketry | 303-174 (21-540) | Angle Gauge, Bolt Tightening | | 100-D002 | Dial Indicator/Magnetic Base | - | Commercially available | | 308-021 | Clutch Housing Alignment Adapter | - | Commercially available | Section 205-02: Rear Drive Axle/Differential | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-001 | Impact Slide Hammer | 205-176 (15-074) | Remover, Differential Bearing Cone | | 205-001 | Differential Carrier Spreader | 205-250 (15-081) | Spreader, Rear Axle Housing | | 205-011 | Pinion Bearing Cone Replacer | 308-112 (16-043A) | Installer, Output Drive Flange Oil Seal | | 205-054 | Cup Replacer | 205-066 (15-033) | Installer, Differential Bearing Cone | | 205-090 | Axle Bearing/Seal Plate | - | Not required | | 205-104 | Aligning Adapter | 205-516 (15-121) | Gauge, Master Pinion | | 205-108 | Gauge Tube | 205-516 (15-121) | Gauge, Master Pinion | | 205-109 | Screw | 205-516 (15-121) | Gauge, Master Pinion | | 205-110 | Gauge Block | 205-516 (15-121) | Gauge, Master Pinion | | 205-111 | Handle | 205-516 (15-121) | Gauge, Master Pinion | | 205-136 | Differential Housing Spreader | 205-250 (15-081) | Spreader, Rear Axle Housing | | 205-153 | Handle | - | Not required | | 205-175 | Socket, Drive Pinion Nut | 205-175 (15-073) | Socket, Drive Pinion Nut | | 205-195 | Axle Bearing Replacer | 205-066-01 (15-033-01) | Adaptor for 205-066 (15-033) | | 205-204 | Gauge Disc | 205-516 (15-121) | Gauge, Master Pinion | | 205-206 | Differential Bearing Replacer | 205-207A (15-120) | Gauge, Differential Dummy Bearing | | 205-207A | Master Bearing Set | 204-044-03A (15-008-03A) | Adaptor for 205-044 (15-008) | | | | 205-058 (15-019) | Adjustment Gauge, Drive Pinion | | | | 205-516 (15-121) | Gauge, Master Pinion | | 205-249 | Outer Pinion Bearing Remover | 205-176 (15-074) | Remover, Differential Bearing Cone | | 205-350 | Axle Seal Replacer | 307-028 (17-002) | Installer, Extension Housing Oil Seal | | 205-503 | Nut Remover | 205-503 (15-119) | Nut, Remover | | 205-D016 | Step Plate | - | Commercially available | | 205-D036 | Pinion and Carrier Puller | - | Commercially available | | 307-003 | Holding Fixture | 205-329 (15-105A) | Mounting Bracket, Engine/Differential | | | | 303-435-06 (21-031B) | Mounting Bracket for 303-435 (21-187) | | 308-125 | Bearing Cup Remover | 303-124 (21-070) | Aligner | Section 205-04: Front Drive Halfshafts | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 205-343 | CV Boot Clamp | 204-169 (14-044) | Clamping Tool, Boot Retaining Clamp | | 205-D069 | Front Hub Replacer | 204-161 (14-041) | Installer, Halfshaft | | 205-D070 | Front Hub Remover | - | Commercially available | | 211-105 | Tie Rod End Remover | - | Commercially available | Section 205-05: Rear Drive Halfshafts | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 205-241 | CV Joint Puller | 204-226 (16-092) | Remover, Halfshaft | | 205-343 | CV Boot Clamp Installer | 204-169 (14-044) | Clamping Tool, Boot Retaining Clamp | | 205-D070 | Front Hub Remover | - | Commercially available | Section 206-00: Brake System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 104-00064 | Brake Bleeder | - | Leitenberger UN04 or equivalent | | 134-R0199 | Tire and Wheel Runout Gauge Set | - | Commercially available | | 416-D002 | Vacuum Pump | 416-D001 (23-036A) | Hand Vacuum/Pressure Pump | | 418-F048 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 206-02: Drum Brake | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 206-0002 | Brake Adjustment Gauge | - | Commercially available | | 134-R0191 | Brake Drum Gauge | - | Commercially available | Section 206-09: Anti-Lock Control | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0053 | FLUKE 88 Digital Multimeter | - | Leitenberger MT04 or equivalent | | 105-R0057 | 73III Digital Multimeter | - | Leitenberger MT04 or equivalent | | 418-005 | EEC-IV 60-Pin Breakout Box | 418-S006 (29-001) | Breakout Box | | 418-063 | Anti-Lock Brake Adapter | 418-006-10 (29-015) | Test Lead No. 18, ECU | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 211-00: Steering System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 023-R0007 | Dial Thermometer 0-220°F | - | Commercially available | | 105-R0057 | 73 III Automotive Meter | - | Leitenberger MT04 or equivalent | | 211-001 | Tie Rod End Remover Tool | - | Commercially available | | 211-034 | Spring Scale | - | Commercially available | | 211-F001 | Power Steering Analyzer | 211-190 (13-018) | Pressure Gauge, Power Steering | | 416-D002 | Vacuum Pump Kit | 416-D001 (23-036A) | Hand Vacuum/Pressure Pump | | 418-F102 | Tach Adapter | - | Commercially available | Section 211-02: Power Steering | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 211-105 | Tie Rod End Remover | - | Commercially available | | 211-185 | Pump Pulley Replacer | 211-198 (13-021) | Remover, Power Steering Pump Pulley | | 211-D027 | Teflon Seal Replacer Set | - | Commercially available | | 303-050 | Engine Lifting Bracket | 303-122 (21-068A) | Lifting Bracket, Engine | | 303-F072 | 3-Bar Engine Support Kit | 303-290 (21-140) | Support Bar, Engine | | | | 303-290-01 (21-140-01) | Adaptor for 303-290 (21-140) | | | | 303-290-02 (21-140-02) | Adaptor for 303-290 (21-140) | | | | 303-290-03 (21-140-03) | Adaptor for 303-290 (21-140) | Section 211-03: Steering Linkage | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 211-105 | Tie Rod End Remover | - | Commercially available | Section 211-04: Steering Column | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 418-F468 | Diagnostic Simulator, Restraint System (4 required) | 501-041 (40-015) | Simulator, Air Bag | | 418-F470 | Diagnostic Simulator, Restraint System (2 required) | 418-F470 (40-020) | Simulator, Air Bag | Section 211-05: Steering Column Switches | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive meter | - | Leitenberger MT04 or equivalent | Section 303-00: Engine System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-001 | Impact Slide Hammer | 205-047 (15-011) | Slide Hammer | | 100-002 | Dial Indicator with Bracketry | 303-174 (21-540) | Angle Gauge, Bolt Tightening | | 303-004 | Valve Stem Checking Tool | - | Commercially available | | 303-006 | Valve/Clutch Spring Tester | - | Commercially available | | 303-D027 | Feeler Gauge Set | - | Commercially available | | 303-D031 | Plastigage | - | Commercially available | | 303-D033 | Piston Ring Groove Cleaner | - | Commercially available | | 303-D039 | Straight Edge | - | Commercially available | Section 303-01A: Engine - 2.0L | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 014-00072 | Heavy Duty Floor Crane | - | Commercially available | | 014-00232 | Engine Stand | 303-435 (21-187) | Mounting Stand | | 134-00251 | Mobile Lift Table | - | Commercially available | | 205-153 | Handle | - | Not required | | 303-103 | Flywheel Holding Tool | 303-254 (21-135) | Locking Tool, Flywheel | | | | 303-393 (21-168) | Locking Tool Flywheel | | 303-164 | Oil Seal Replacer | 303-149 (21-093A) | Installer, Timing Cover Oil Seal | | 303-300 | Valve Spring Compressor Set | 303-361 (21-155) | Compressor, Valve Spring | | | | 303-361-02 (21-155-02A) | Adaptor for 303-361 (21-155) | | 303-328 | Rear Oil Seal Replacer | 303-291 (21-141) | Installer, Crankshaft Rear Oil Seal | | 303-329 | Oil Seal Pilot | 303-291 (21-141) | Installer, Crankshaft Rear Oil Seal | | 303-350 | Valve Spring Compressor | 303-361 (21-155) | Compressor, Valve Spring | | | | 303-361-02 (21-155-02A) | Adaptor for 303-361 (21-155) | | 303-409 | Seal Remover | 303-293 (21-143) | Remover, Crankshaft Oil Seal | | 303-464 | Camshaft Seal Replacer | 303-039 (21-009B) | Installer, Timing Cover Oil Seal | | 303-465 | Camshaft Alignment Timing Tool | 303-376 (21-162B) | Timing Plate, Camshaft Alignment | | 303-468 | Valve Stem Seal Remover | 303-374 (21-160) | Remover, Valve Stem Oil Seal | | | | 303-508 (21-211) | Pliers, Valve Stem Oil Seal | | 303-470 | Valve Stem Seal Replacer | - | Not required | | 303-574 | Crankshaft TDC Timing Peg | 303-574 (21-163) | Timing Peg, Crankshaft TDC | | 303-D032 | Piston Ring Compressor | - | Commercially available | | 303-D089 | Spreader Bar | - | Commercially available | | 303-F072 | 3 Bar Engine Support Kit | 303-290 (21-140) | Support Bar, Engine | | | | 303-290-01 (21-140-01) | Adaptor for 303-290 (21-140) | | | | 303-290-02 (21-140-02) | Adaptor for 303-290 (21-140) | | | | 303-290-03 (21-140-03) | Adaptor for 303-290 (21-140) | | 303-S02A | Pin Remover/Replacer | - | Commercially available | | 307-005 | Impact Hammer | - | Commercially available | | 308-001 | Puller With Slide Hammer | - | Commercially available | | 308-020 | Clutch Aligner | 308-204 (16-067) | Aligner, Clutch Plate | | 308-157 | Pilot Bearing Installer | 303-090 (21-045) | Installer, Crankshaft Pilot Bearing | | 310-D005 | Remover, Fuel Pipe 1/2 inch (green) | 310-D005 (23-040) | Disconnect Tool, Spring Lock Coupling (1/2" green) | Section 303-01B: Engine - 3.0L | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 014-00765 | Powertrain Lift with Tilting Plate | - | Commercially available | | 100-002 | Dial Indicator with Bracketry | 303-174 (21-540) | Angle Gauge, Bolt Tightening | | 211-105 | Tie Rod End Remover | - | Commercially available | | 211-185 | Pump Pulley Replacer | 211-198 (13-021) | Remover, Power Steering Pump Pulley | | 303-009 | Crankshaft Damper Remover | 303-338 (21-153B) | Remover, Crankshaft Vibration Damper | | 303-016 | Cylinder Ridge Reamer | - | Commercially available | | 303-050 | Engine Lifting Brackets | 303-122 (21-068A) | Lifting Bracket, Engine | | 303-102 | Crankshaft Damper Replacer | 303-130 (21-076) | Remover/Installer, Crankshaft Vibration Damper | | 303-178 | Rear Main Seal Replacer | 303-460 (21-193A) | Installer, Crankshaft Rear Oil Seal | | 303-300 | Valve Spring Compressor Set | 303-361 (21-155) | Compressor, Valve Spring | | | | 303-361-02 (21-155-02A) | Adaptor for 303-361 (21-155) | | | | 303-461 (21-194) | Compressor, Valve Spring | | | | 303-461-01 (21-194-01) | Adaptor for 303-461 (21-194) | | 303-335 | Crankshaft Seal Installer / Aligner | 303-055 (21-017A) | Installer/Aligner, Timing Cover Oil Seal | | 303-346 | Valve Guide Replacer | - | Not required | | 303-350 | Valve Spring Compressor | 303-361 (21-155) | Compressor, Valve Spring | | | | 303-361-02 (21-155-02A) | Adaptor for 303-361 (21-155) | | | | 303-461 (21-194) | Compressor, Valve Spring | | | | 303-461-01 (21-194-01) | Adaptor for 303-461 (21-194) | | 303-384 | Rear Crankshaft Adapter Bolts | - | Not required | | 303-409 | Seal Remover | 303-508 (21-211) | Pliers, Valve Stem Oil Seal | | 303-462 | Connecting Rod Guide Set | - | Commercially available | | 303-463 | Camshaft Seal Protector | - | Commercially available | | 303-464 | Camshaft Seal Replacer | 303-458 (21-192) | Installer, Camshaft Pulley | | | | 303-458-01 (21-192-01) | Adaptor for 303-458 (21-192) | | 303-470 | Valve Stem Seal Replacer | 303-247 (21-130A) | Installer, Intake Valve Stem Oil Seal | | 303-473 | Valve Spring Compressor | 303-361 (21-155) | Compressor, Valve Spring | | | | 303-361-02 (21-155-02A) | Adaptor for 303-361 (21-155) | | | | 303-461 (21-194) | Compressor, Valve Spring | | | | 303-461-01 (21-194-01) | Adaptor for 303-461 (21-194) | | 303-519 | Rear Crankshaft Seal Remover | 303-293 (21-143) | Remover, Crankshaft Oil Seal | | 303-544 | Flywheel Holding Tool | 303-254 (21-135) | Locking Tool, Flywheel | | | | 303-393 (21-168) | Locking Tool, Flywheel | | 303-F072 | 3-Bar Engine Support Kit | 303-361 (21-155) | Compressor, Valve Spring | | | | 303-361-02 (21-155-02A) | Adaptor for 303-361 (21-155) | | | | 303-461 (21-194) | Compressor, Valve Spring | | | | 303-461-01 (21-194-01) | Adaptor for 303-461 (21-194) | | 303-S455 | Water Pump Pulley Remover/Replacer | 303-338-02 (21-153A-02) | Adaptor for 303-338 (21-153) | | | | 303-338 (21-153B) | Remover, Crankshaft Vibration Damper | | | | 303-458 (21-192) | Installer, Camshaft Pulley | | | | 303-458-01 (21-192-01) | Adaptor for 303-458 (21-192) | | 307-005 | Impact Slide Hammer | 205-047 (15-011) | Slide Hammer | Section 303-03: Engine Cooling | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 014-R1060 | Battery/Anti-Freeze Tester | - | Commercially available | | 014-R1072 | Radiator/Heater Core Pressure Tester | 303-396 (24-001A) | Pressure Tester, Cooling System | | 023-00154 | Pro Flush & Fill ® Coolant Flush & Fill | - | Commercially available | | 164-R3658 | Flush Kit Hardware Package | - | Commercially available | | 164-R3662 | Drain Kit | - | Commercially available | | 418-F082 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | | R05-R0057 | 73III Automatic Meter | - | Commercially available | Section 303-04A: Fuel Charging and Controls - 2.0L | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 310-D005 | Fuel Pipe 1/2 inch Remover (Green) | 310-D005 (23-040) | Disconnect Tool, Spring Lock Coupling (1/2" green) | Section 303-13: Evaporative Emissions | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 310-F007 | Evaporative Emission System Leak Tester | - | Commercially available | Section 303-14: Electronic Engine Controls | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 303-476 | EGO Sensor Wrench | - | Commercially available | Section 307-01: Automatic Transmission/Transaxle | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 007-00125 | CD4E Cable and Overlay | - | Commercially available | | 007-00129 | MLP-D Cable: CD4E "94 and Up | - | Commercially available | | 007-00130 | Transmission Tester (only) | - | Commercially available | | 014-00950 | EEC-V 104-Pin Breakout Box | - | Commercially available | | 100-001 | Slide Hammer | 205-047 (15-011) | Slide Hammer | | 100-002 | Dial Indicator Gauge with Bracketry | 303-174 (21-540) | Angle Gauge, Bolt Tightening | | 100-010 | Remover, O-Ring Seal | 100-010 (17-063) | Remover, O-Ring | | 100-D002 | Holding Fixture, Dial Indicator Gauge | - | Commercially available | | 105-R0057 | 73III Digital Multimeter | - | Leitenberger MT04 or equivalent | | 164-R0751 | 12 Volt UV Spot Lamp Kit | - | Leitenberger UVL01 or equivalent | | 205-098 | Drawbar, Rear Axle | 205-066 (15-033) | Installer, Differential Bearing Cone | | 205-153 | Handle, Universal | - | Not required | | 303-290A | 3 Bar Engine Support Bar | 303-290 (21-140) | Support Bar, Engine | | 303-290A-01 | Cat Walk Adapters | 303-290-01 (21-140-01) | Adaptor for 303-290 (21-140) | | 303-290A-03A | Engine Support Leg | 303-290-02 (21-140-02) | Adaptor for 303-290 (21-140) | | 303-D011 | Actuator Pin, Dia 3/16" | 303-290-03 (21-140-03) | Adaptor for 303-290 (21-140) | | 303-D019 | 3/4 Blind Hole Puller Collet | - | Commercially available | | 303-D026 | Depth Micrometer | - | Commercially available | | 303-D089 | Engine Lifting Chains (Part of Spreader Bar) | 303-290-07 (21-140-07) | Adaptor for 303-290 (21-140) | | 307-002 | Installer, Shift Shaft Oil Seal | - | 13mm socket (long) | | 307-003 | Holding Fixture, Transmission | 303-435-06 (21-031B) | Mounting Bracket for 303-435 (21-187) | | | | 205-329 (15-105A) | Mounting Bracket, Engine/Differential | | 307-015 | Compressor, Clutch Spring | 307-015 (17-058) | Compressor, Clutch Spring | | 307-071 | End Play Checking Tool | 307-267 (17-062) | Gauge, Torque Converter End Play | | 307-091 | Torque Converter Handles | - | Not required | | 307-097 | Installer, Throttle Shaft Seal | 308-113 (16-044) | Installer, Input Shaft Oil Seal | | 307-109 | Cross Block | 205-311 (15-092) | Remover, Bearing/Gear | | 307-126 | Test Plate Screw Set, Transmission | 307-301 (17-056) | Plate, Transmission Air Test | | 307-127 | Aligner, Oil Pump Housing | - | Not required | | 307-157 | Installer, Output Halfshaft Oil Seal | 205-077 (15-047A) | Installer, Drive Pinion Oil Seal | | 307-240 | Installer, Lube Tube Oil Seal | 307-050 (17-008) | Installer, Shift Shaft Oil Seal | | 307-273 | Installer, Torque Converter Oil Seal | 307-273 (17-052) | Installer, Torque Converter Oil Seal | | 307-280 | Protector, Piston Seal | 307-275 (17-060-01) | Protector, Piston Seal | | 307-281 | Protector, Piston Seal | 307-276 (17-060-02) | Protector, Piston Seal | | 307-282 | Protector, Piston Seal | 307-277 (17-060-03) | Protector, Piston Seal | | 307-283 | Protector, Piston Seal | 307-278 (17-060-04) | Protector, Piston Seal | | 307-284 | Protector, Piston Seal | 307-279 (17-060-05) | Protector, Piston Seal | | 307-286 | Remover/Installer, Needle Bearing | 307-286 (17-064) | Remover/Installer, Needle Bearing | | 307-287 | Installer/Remover Servo Plug | 204-168 (14-043) | Remover/Installer, Lower Arm Bushing | | 307-288 | Mounting Plate | 303-435-13 (21-170A) | Mounting Plate for 303-435-06 (21-031) | | 307-288 | Fixture, CD4E Holding | 303-435-06 (21-031B) | Mounting Bracket for 303-435 (21-187) | | 307-289 | Remover, Transmission Oil Pump | 205-047 (15-011) | Slide Hammer | | | | 307-272 (17-061) | Remover, Torque Converter Oil Seal | | 307-294 | Installer, Needle Bearing | 307-294 (17-053) | Installer, Needle Bearing | | 307-295 | Remover/Installer, Servo Cover | 204-168 (14-043) | Remover/Installer, Lower Arm Bushing | | 307-299 | Aligner Valve Body | 307-299 (17-054) | Alignment Pins, Valve Body | | 307-300 | Gauge, Shim Selection Bar | 307-300 (17-055) | Gauge Bar, Shim Selection | | 307-300-01 | Depth Gauge, Shim Selection | 307-300-01 (17-055-01) | Adapter for 307-300 (17-055) | | 307-301 | Transmission Test Plate | 307-301 (17-056) | Plate, Transmission Air Test | | 307-304 | Preload Plate, Shim Selection | 307-304 (17-057) | Preload Plate, Shim Selection | | 307-304-01 | Plate, Shim Selection Preload | 307-304-01 (17-057-01) | Adapter for 307-304 (17-057) | | 307-304-02 | Aligner Shim Selection | 307-304-02 (17-057-02) | Adapter for 307-304 (17-057) | | 307-304-03 | Aligner Shim Selection | 307-304-03 (17-057-03) | Adapter for 307-304 (17-057) | | 307-306 | Lube Tube Replacer Set | - | Not required | | 307-307 | Installer, Lube Tube | 307-307 (17-065) | Installer, Lube Tube | | 307-308 | Aligner, End Play Gauge | 307-267 (17-062) | Gauge, Torque Converter End Play | | 307-346 | Torque Converter Holding Tool | - | Not required | | 307-351 | TRS Alignment Tool | 307-351 (17-090) | Alignment Gauge, TR Sensor | | 307-428 | Installer, Oil Seal | 307-440 (17-089) | Installer, Oil Seal | | 307-429 | Remover, Oil Seal | 205-078 (15-048) | Remover, Drive Pinion Oil Seal | | | | 308-208 (16-074) | Remover, Halfshaft Oil Seal | | 307-F015 | Torque Converter Leak Tester | - | Commercially available | | 307-S290 | Set, Selector Shaft Alignment Service | 307-S290 (17-066) | Aligner, Selector Shaft | | 307-S296 | Rod Selector, Servo Piston | 307-S296 (17-059) | Rod Selector, Servo Piston | | 308-125 | Remover, Transfer Case Bearing Cup | 303-124 (21-070) | Aligner | | 308-201 | Input Shaft Bearing Remover | - | Commercially available (Schrem) | | 308-375 | Remover, Input Shaft Oil Seal | 307-272 (17-061) | Remover, Torque Converter Oil Seal | | 309-001 | Exhaust Holder Tool | 309-001 (25-001) | Holding Fixture, Flexible Exhaust Pipe | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 307-02: Transmission/Transaxle Cooling | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 307-F011 | Torque Converter Cleaner | - | Commercially available | Section 307-05: Automatic Transmission/Transaxle External Controls | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 303-D027 | Feeler Gage Set | - | Commercially available | Section 308-00: Manual Transmission/Transaxle and Clutch - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-D002 | Dial Indicator with Magnetic Base | - | Commercially available | Section 308-01: Clutch | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-D002 | Dial Indicator with Magnetic Base | - | Commercially available | | 205-153 | Handle | - | Not required | | 303-103 | Flywheel Holding Tool | 303-254 (21-135) | Locking Tool, Flywheel | | | | 303-393 (21-168) | Locking Tool, Flywheel | | 308-001 | Puller With Slide Hammer | - | Commercially available | | 308-020 | Clutch Aligner | 308-204 (16-067) | Aligner, Clutch Plate | | 308-157 | Pilot Bearing Installer | 303-090 (21-045) | Installer, Crankshaft Pilot Bearing | Section 308-03: Manual Transmission/Transaxle | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-001 | Impact Slide Hammer | 205-047 (15-011) | Slide Hammer | | 204-039 | Front Hub Bearing Cup | 205-051 (15-015) | Installer, Driveshaft Oil Seal | | 205-055 | Universal Bearing Puller | - | Commercially available | | 205-090 | Axle Bearing/Seal Plate | 308-046 (16-016) | Installer, Extension Housing Bushing/Oil Seal | | 205-116 | Differential Bearing Cone Remover | 205-176 (15-074) | Remover, Differential Bearing Cone | | 205-153 | Handle | 205-176 (15-074) | Remover, Differential Bearing Cone | | 205-D064 | Bearing Puller | - | Commercially available | | 205-DS004 | Shaft Protector Set | 202-295 (15-050A) | Remover, Bearing | | 205-DS011 | Step Plate Adapter Set | 205-071 (15-026A-01) | Remover, Differential Bearing | | 205-DS023 | Push Puller Set | 202-295 (15-050A) | Remover, Bearing | | 206-007 | Brake Piston Remover | - | Commercially available | | 303-DS005 | Blind Hole Puller Set | - | Commercially available | | 303-F072 | Three Bar Engine Support Kit | 303-290 (21-140) | Support Bar, Engine | | | | 303-290-01 (21-140-01) | Adapter for 303-290 (21-140) | | | | 303-290-02 (21-140-02) | Adapter for 303-290 (21-140) | | | | 303-290-03 (21-140-03) | Adapter for 303-290 (21-140) | | 307-003 | Holding Fixture | 205-329 (15-105A) | Mounting Bracket, Engine/Differential | | | | 303-435-06 (21-031B) | Mounting Bracket for 303-435 (21-187) | | 307-050 | Installer, Shift Shaft Oil Seal | 307-050 (17-008) | Installer, Shift Shaft Oil Seal | | 307-163 | Bearing Remover | - | Commercially available | | 307-181 | Bearing Cone Replacer | 308-046 (16-016) | Installer, Extension Housing Bushing/Oil Seal | | 308-001 | Puller With Slide Hammer | 205-078-01 (15-048-01) | Adapter for 205-078 (15-048) | | 308-047 | Bearing Cup Remover | 205-078 (15-048) | Remover, Drive Pinion Oil Seal | | 308-057 | Bell Housing Seal Replacer | 205-077 (15-047A) | Installer, Drive Pinion Oil Seal | | 308-119 | Installer, Halfshaft Oil Seal | 308-119 (16-071) | Installer, Halfshaft Oil Seal | | 308-155 | Bearing Cone Replacer | 308-046 (16-016) | Installer, Extension Housing Bushing/Oil Seal | | 308-160 | Torque Adapter | - | Not required | | 308-161 | Shim Selection Set | 308-233 (16-081) | Holding Fixture, Bearing Preload | | 308-162 | Differential Bearing Cup Replacer | 205-296 (15-085) | Installer, Rear Hub Bearing Cone/Oil Seal | | 308-164 | Shim Selection Tool Set | 308-206 (16-069) | Spacers, Transmission Housing | | 308-165 | Rotating Tool | 308-165 (16-072) | Rotator, Differential | | 308-169 | Bearing Cone Replacer | 308-046 (16-016) | Installer, Extension Housing Bushing/Oil Seal | Section 308-07A: Four-Wheel Drive Systems | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | Section 308-07B: Transfer Case | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-001 | Slide Hammer | 205-047 (15-011) | Slide Hammer | | 205-126 | Holding Fixture, Drive Pinion Flange | 205-072 (15-030A) | Flange Holding Wrench, Universal | | 205-155 | Installer, Rear Axle Oil Seal | 204-288 (14-063) | Remover/Installer, Ball Joint | | 211-014 | Remover, Steering Wheel | 211-014 (13-019) | Remover, Steering Wheel | | 308-427 | Installer, PTO Shaft Inner/Outer Oil Seal | 205-296 (15-085) | Installer, Rear Hub Bearing Cone/Oil Seal | | 308-428 | Remover, PTO Driven Gear Oil Seal | - | Commercially available | | 308-429 | Installer, PTO Driven Gear Oil Seal | 308-113 (16-044) | Installer, Input Shaft Oil Seal | | 308-430 | Installer, PTO Drive Gear Outer Oil Seal | 205-077 (15-047A) | Installer, Drive Pinion Oil Seal | | 308-431 | Installer, Halfshaft Oil Seal | 205-064 (15-028) | Socket, Axle Nut (65 mm) | | 308-432 | Installer, PTO Dust Flange | 308-013 (16-008) | Remover/Installer, Mounting Bushing | Section 309-00: Exhaust System | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 303-476 | Oxygen Sensor Wrench | - | Commercially available | Section 310-00: Fuel System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 310-012 | Fuel Pressure Gauge | 310-025 (23-024) | Fuel Pressure Gauge | | 310-D005 | Fuel Pipe 1/2 Inch Remover (Green) | 310-D005 (23-040) | Disconnect Tool, Spring Lock Coupling (1/2" green) | Section 310-01: Fuel Tank and Lines | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 310-069 | Fuel Sender Wrench | 310-069 (23-055) | Wrench, Fuel Tank Sender Unit | | D80-23200-A | Heavy-Duty Riveter | - | Commercially available | Section 310-03: Vehicle Speed Control | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | Section 412-00: Climate Control System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 014-R1054 | Vacuum Tester | 416-D001 (23-036A) | Hand Vacuum/Pressure Pump | | 014-R1072 | Pressure Tester | - | Commercially available | | 023-00153 | R-134a A/C Refrigerant Center | - | Leitenberger CCS02 or equivalent | | 023-R0162 | 1.2 CFM Vacuum Pump | - | Leitenberger CCS01 or equivalent | | 023-R0163 | 4.0 CFM Vacuum Pump | - | Commercially available | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 164-R0721 | 120 Watt UV Spot Lamp | - | GV-2931 | | 164-R0775 | R-134a Fluorescent Tracer Dye Injector | - | Leitenberger UVL01 or GV-2932 | | 164-R3712 | R-134a Fluorescent Tracer Dye | - | Leitenberger LT1004 or equivalent | | 176-00002 | R-134a A/C Service Center | - | Commercially available | | 176-R032A | R-134a Manifold Gauge Set | - | Leitenberger PM01.1 or equivalent | | 198-00003 | Refrigerant Identifier with Air-Radicator | - | Commercially available | | 216-00001 | Refrigerant Leak Detector | - | Leitenberger ELS01 or equivalent | | 219-00001 | A/C Flush and Purge Machine | - | Commercially available | | 219-00020 | A/C Flush and Purge Fitting Kit | - | Commercially available | | 412-039 | Spring Lock Coupling Disconnect Tool Set | 310-026 (23-023A) | Disconnect Tool, Spring Lock Coupling (3/8" red) | | | | 412-027 (34-001) | Disconnect Tool, Spring Lock Coupling (1/2" blue) | | | | 412-069 (34-002) | Disconnect Tool, Spring Lock Coupling( 3/4" white) | | | | 412-038 (34-003) | Disconnect Tool, Spring Lock Coupling (5/8" black) | | 412-093 | A/C Pressure Test Adapter | - | Not required | | 412-DS028 | R-12/R-134a Air Conditioning Test Fitting Set | 412-101 (34-011) | Adapter Kit, Flush Filter (1/2") | | | | 412-107 (34-016) | Adapter Kit, Quick Release Coupling (5/8") | | 416-D002 | Vacuum Pump Kit | 416-D001 (23-036A) | Hand Vacuum/Pressure Pump | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 412-03: Air Conditioning | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-010 | O-Ring Seal Remover | 100-010 (17-063) | Remover, O-Ring | | 205-116 | Differential Bearing Cone Remover | 205-176 (15-074) | Remover, Differential Bearing Cone | | 205-D026 | 2-Jaw Puller | - | Commercially available | | 412-034 | Fixed Orifice Tube Tool | 412-034 (34-004) | Remover/Installer, Fixed Orifice | | 412-035 | Broken Orifice Extractor | 412-035 (34-005) | Remover, Broken Orifice | | 412-058 | Shaft Seal Installer | - | Not required | | 412-059 | Compressor Seal Remover | - | Not required | | 412-061 | Seal Protector | - | Not required | | 412-063 | Snap Ring Remover | - | Not required | | 412-065 | Coil Replacer | - | Not required | | 412-067 | Field Coil Remover | - | Not required | | 412-078 | Field Coil Replacer | - | Not required | | 412-098 | Compressor Clutch Holding Tool | - | Not required | Section 412-04: Control Components | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 412-D024 | Alignment Pin, Temperature Blend Door | - | Commercially available | Section 413-00: Instrument Cluster and Panel Illumination | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 413-01: Instrument Cluster | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 014-R1063 | Instrument Gauge System Tester | - | Commercially available | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 413-06: Horn | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | Section 413-09: Warning Devices | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 414-00: Charging System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 010-00736 | SABRE Premium Electrical System Tester | - | Commercially available | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 414-01: Battery, Mounting and Cables | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 162-00004 | Battery Analyzer | - | Commercially available | Section 415-00: Entertainment System - General Information | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | Section 415-01: Audio Unit | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 415-001 | Radio Removing Tool | - | Commercially available | Section 417-01: Exterior Lighting | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 417-02: Interior Lighting | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 418-00: Module Communications Network | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 107-R0300 | Heat Gun | - | Commercially available | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 418-01: Module Configuration | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 418–F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F120 | Flash Cable | - | Commercially available | | 418–F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 419-01A: Anti-Theft - Active | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 419-01B: Anti-Theft - Passive | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 419-10: Multifunction Electronic Control Modules | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 501-09: Rear View Mirrors | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | Section 501-10: Seating | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F468 | Diagnostic Simulator, Restraint System | 501-041 (40-015) | Simulator, Air Bag | | 418-F470 | Diagnostic Simulator, Restraint System | 418-F470 (40-020) | Simulator, Air Bag | Section 501-11: Glass, Frames and Mechanisms | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 107-R0300 | Heat Gun | - | Commercially available | | 107-R1511 | Pneumatic Knife with Offset Blade | - | Commercially available | | 164-R2450 | Interior Auto Glass Cut-Out Knife Kit | - | Commercially available | | 164-R2459 | The Pumper | - | Commercially available | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 501-14: Handles, Locks, Latches and Entry Systems | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 501-16: Wipers and Washers | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 010-00736 | SABRE Electrical System Tester | - | Commercially available | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 501-17: Roof Opening Panel | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224 | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | Section 501-20A: Occupant Restraints - Active | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 100-F012 | D-Ring Installation Kit | - | Commercially available | | 501-010 | Seat Belt Bolt Bit | - | Commercially available | Section 501-20B: Occupant Restraints - Passive | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 105-R0057 | 73III Automotive Meter | - | Leitenberger MT04 or equivalent | | 418-F052 | New Generation STAR (NGS) Tester | - | Worldwide Diagnostic System (WDS) | | 418-F224, | Worldwide Diagnostic System (WDS) | - | Worldwide Diagnostic System (WDS) | | 418-F468 | Diagnostic Tool, Restraint System (4 Req'd) | 501-041 (40-015) | Simulator, Air Bag | | 418-F470 | Diagnostic Tool, Restraint System (2 Req'd) | 418-F470 (40-020) | Simulator, Air Bag | Section 502-00: Uni-Body, Subframe and Mounting System | North American Special Tool Number | North American Special Tool Name | European Special Tool Number | European Special Tool Name | | 303-F072 | Three-Bar Engine Support Kit | 303-290 (21-140) | Support Bar, Engine | | | | 303-290-01 (21-140-01) | Adapter for 303-290 (21-140) | | | | 303-290-02 (21-140-02) | Adapter for 303-290 (21-140) | | | | 303-290-03 (21-140-03) | Adapter for 303-290 (21-140) | |
