ford Workshop Repair Guides

Ford Workshop Service and Repair Manuals

ABOUT US
303-01A Engine - 1.8L Duratec-SCi (MI4)|Description and Operation > < Bearing Inspection

Mondeo 2001 (10.2000-02.2007)

Engine - 1.8L Duratec-SCi (MI4) - Specifications Mondeo 2001 (10/2000-02/2007)

Engine Data

Description
Engine Code CFBA
Firing order 1-3-4-2
Bore 83 mm
Stroke 83.1 mm
Cubic Capacity 1798
Compression ratio 10.8:1
Power output at 6000 130 PS (96 kW)
Max. torque at 4250 175 Nm
Maximum engine speed (continuous) 6800 rpm
Idle speed 700 rpm
Number of main bearings 5
Camshaft drive Chain
Maximum oil consumption 0.5L/1000km

Engine Oil

Description Viscosity Specification
Recommended engine oil
Ford Formula E SAE 5W-30 WSS-M2C913-A or WSS-M2C913-B
Alternative engine oils
Ford Formula S SAE 5W-40 ACEA A3/B3
Ford XR+ High Performance SAE 10W-40 ACEA A3/B3

Lubricants, Fluids, Sealers and Adhesives

Item Specification
Sealant, oil pan contact surface to oil seal carrier, oil pan to cylinder block, oil pan to front cover WSE-M4G323-A4

Oil system

Description bar
Pressure relief valve opening pressure 5

Engine Oil Capacity

Description Liters
Initial fill, including oil filter 4.6
Service fill including filter 4.3
Service fill excluding filter 3.9

Valve Dimensions

Description mm
Valve clearance (engine cold), intake 0.22 - 0.28
Valve clearance (engine cold), exhaust 0.27 - 0.33
Valve stem diameter, intake 5.465 - 5.480
Valve stem diameter, exhaust 5.470 - 5.485

Camshaft Dimensions

Description mm
Camshaft journal diameter 24.97 ± 0.01
Camshaft journal clearance 0.055 - 0.060
Camshaft end play 0.09 - 0.24
Camshaft lobe lift, intake 8.5
Camshaft lobe lift, exhaust 7.7

Crankshaft Dimensions

Description mm
Crankshaft main bearing journal 0.019 - 0.035
Crankshaft main bearing journal diameter 57.018 - 57.040
Crankshaft end play 0.335 ± 0.115

Piston Dimensions

Description mm
Piston diameter - Class 1 82.965 - 82.975
Piston diameter - Class 2 82.975 - 82.985
Piston diameter - Class 3 82.985 - 82.995

Piston Ring Dimensions

Description mm
Piston ring end gap (oil control ring) 0.2 - 0.7

Cylinder Head

CAUTION:
CAUTION:The mating face of the cylinder head must not be reworked.
Description mm
Maximum distortion (mating face) 0.1

Cylinder Block

Description mm
Cylinder bore diameter 83.000 + 0.030
Cylinder block distortion (maximum) 0.1

Connecting Rod Dimensions

Description mm
Large end bore diameter 50.035 ± 0.01

Torque Specifications

Description Nm lb-ft lb-in
Cylinder head retaining bolts a) - -
Timing chain guide retaining bolts 10 - 89
Camshaft bearing caps retaining bolts a) - -
Camshaft sprocket retaining bolts 72 53 -
Camshaft position (CMP) sensor retaining bolt 6 - 53
Engine front cover retaining bolts a) - -
Crankshaft pulley retaining bolts a) - -
Crankshaft position (CKP) sensor bracket retaining bolts 7 - 62
Crankshaft rear seal retaining bolts 10 - 89
Coolant pump pulley retaining bolts 25 18 -
Coolant pump retaining bolts 10 - 89
Coolant expansion tank retaining nut 10 - 89
Coolant plug to cylinder block 43 32 -
Coolant plugs (4) to cylinder head 75 55 -
Power steering pump retaining bolt 23 17 -
Power steering reservoir retaining bolts 25 18 -
Power steering reservoir retaining nut 10 - 89
Power steering pipe to the power steering 65 48 -
Power steering bracket retaining nut 15 11 -
Exhaust manifold bracket retaining bolts 18 13 -
Exhaust manifold upper heat shield retaining bolts 10 - 89
Exhaust manifold lower heat shield retaining bolts 10 - 89
Exhaust manifold to the cylinder head 48 35 -
Exhaust manifold studs to cylinder head 17 13 -
Exhaust gas recirculation (EGR) valve tube to EGR valve retaining nuts (exhaust side) 28 21 -
EGR valve tube to EGR valve retaining bolts (intake side) 25 18 -
EGR valve tube to exhaust manifold retaining bolts 23 17 -
EGR valve tube to intake manifold retaining bolts 11 8 -
Fuel pump retaining bolts 18 13 -
Fuel pump drive assembly retaining bolts 25 18 -
Valve cover retaining bolts 10 - 89
Oil pressure switch 15 11 -
Oil pump retaining bolts a) - -
Oil pan retaining bolts 25 18 -
Oil cooler to oil filter adaptor retaining bolt 34 25 -
Flywheel retaining bolts a) - -
Oil filter adapter retaining bolts 25 18 -
Positive crankcase ventilation housing retaining bolts 10 - 89
Knock sensors retaining bolt 20 15 -
Thermostat housing retaining bolts 10 - 89
Oil pump sprocket retaining bolt 25 18 -
Oil pump chain guide retaining bolts 10 - 89
Oil pump chain tensioner retaining bolt 10 - 89
Accessory drive belt idler pulley retaining bolt 25 18 -
Intake manifold retaining bolts 18 13 -
Transaxle retaining bolts 44 32 -
Transaxle right-hand retaining bolts 44 32 -
Halfshaft center bearing carrier retaining bolts 48 35 -
Intermediate shaft bearing cap retaining nuts 25 18 -
Starter motor retaining bolts 35 26 -
Wiring harness retaining bracket nuts 20 15 -
Air conditioning compressor (A/C) compressor retaining bolts 24 18 -
Engine rear mount retaining nut 80 59 -
Engine front mount studs to front cover 10 - 89
Engine front mount retaining bolts 80 59 -
Top mount retaining nut 59 44 -

a) Refer to the procedure in this section.

303-01A Engine - 1.8L Duratec-SCi (MI4)|Description and Operation > < Bearing Inspection