ford Workshop Repair Guides

Ford Workshop Service and Repair Manuals

Code 451 - 460, ( 452 453 454 455 456 457 458 459 )|System Diagnosis|Page 81 > < Code 411 - 420, ( 412 413 414 415 416 417 418 419 )|System Diagnosis|Page 77
Page 1
background image

Code 451 - 460: Testing and Inspection

NOTE

KOEO refers to Key On Engine Off (KOEO)
KOER refers to Key On Engine Running (KOER)
DTC refers to Diagnostic Trouble Code (DTC)
DTCs should be diagnosed in the order they are received.

DTC 337

Exhaust gas recirculation valve position sensor circuit above maximum voltage.

KOEO Hard Code ....................................................................................................................................................................................  Go to DN5
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/DN - EGR Valve Position Sensor/EGR
Vacuum Regulator Solenoid/DN5 - Attempt to Generate DTC 327

KOER Hard Code ....................................................................................................................................................................................  Go to DN5
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/DN - EGR Valve Position Sensor/EGR
Vacuum Regulator Solenoid/DN5 - Attempt to Generate DTC 327

KOEO Memory Code ............................................................................................................................................................................  Go to DN90
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/DN - EGR Valve Position Sensor/EGR
Vacuum Regulator Solenoid/DN90 - Check Intermittent Sensor

DTC 338

Engine coolant temperature lower than expected (thermostat test).

KOEO Memory Code ...........................................................................................................................................................................  Go to DA100
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/DA - Intake Air and Engine Coolant
Temperature Sensors/DA100 - Engine Too Cold

DTC 339

Engine coolant temperature higher than expected (thermostat test).

KOEO Memory Code ...........................................................................................................................................................................  Go to DA101
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/DA - Intake Air and Engine Coolant
Temperature Sensors/DA101 - Engine Too Hot

DTC 341

Octane adjust service pin open.

KOEO Hard Code .....................................................................................................................................................................................  Go to KP1
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/KP - Octane Adjust/KP1 - Inspect Octane
Adjust Inline Connector

DTC 381

Frequent A/C clutch cycling.

KOEO Memory Code .............................................................................................................................................................................  Go to X130
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/X - Constant Control Relay Module
(CCRM)/X130 - Check For Causes of Fast A/C Compressor Cycling

DTC 411

Cannot control RPM during KOER self-test low RPM check.

KOER Hard Code ...................................................................................................................................................................................  Go to KE15
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/KE - Idle Air Control Control
Solenoid/KE15 - Engine RPM Error During Self-Test

DTC 412

Cannot control RPM during KOER self-test high RPM check.

KOER Hard Code .....................................................................................................................................................................................  Go to KE1
See: Powertrain Management/Computers and Control Systems/Testing and Inspection/Pinpoint Tests/KE - Idle Air Control Control Solenoid/KE1
- Check For RPM Drop

DTC 415

Code 451 - 460, ( 452 453 454 455 456 457 458 459 )|System Diagnosis|Page 81 > < Code 411 - 420, ( 412 413 414 415 416 417 418 419 )|System Diagnosis|Page 77