Transit Connect L4-2.0L (2010)
Engine Control Module: Procedures
FLASH ELECTRICALLY ERASABLE PROGRAMMABLE READ ONLY MEMORY (EEPROM)
Description
The EEPROM is contained in an integrated circuit internal to the powertrain control module (PCM). The EEPROM contains the vehicle strategy
including calibration information specific to the vehicle, and is capable of being programmed or flashed repeatedly.
As part of the calibration there is an area referred to as the vehicle identification (VID) block. The VID block is programmed when installing a new
PCM as described under Programming the VID Block for a Replacement PCM. Failure to carry out this procedure may generate DTC P1635 or
P1639. The VID block in an existing PCM can also be tailored to accommodate various hardware or parameter changes made to the vehicle since
production. Failure to carry out this procedure properly may generate DTC P1635, Tire/Axle Ratio out of Acceptable Range. An incorrect tire/axle
ratio is one of the main causes for DTC P1639. This is described under Making Changes to the VID Block and also under Making Changes to the
PCM Calibration. The VID block contains many items used by the strategy for a variety of functions. Some of these items include the vehicle
identification number (VIN), octane adjust, fuel octane, fuel type, vehicle speed limit, tire size, axle ratio, the presence of speed control, and 4-wheel
drive electronic shift-on-the-fly (ESOF) versus manual shift-on-the-fly (MSOF). Only items applicable to the vehicle hardware and supported by the
VID block are displayed on the scan tool.
When changing items in the VID block, the strategy places range limits on certain items such as tire and axle ratio. The number of times the VID
block may be reconfigured is limited. When this limit is reached, the scan tool displays a message indicating the need to flash the PCM again to reset
the VID block.
On selected vehicles equipped with permanent DTC reporting capabilities, neutral profile correction should be learned after a PCM replacement in
order to activate the misfire monitor. This can be accomplished using the Misfire Monitor Neutral Profile Learn function on the scan tool.
Programming can be carried out by a local Ford dealer or any non-Ford facility. Refer to the scan tool manufacturer's instruction manual for details.
Neutral Profile Correction
In order for the misfire detection system to function properly, any mechanical inaccuracies in the crankshaft position (CKP) sensor must be learned by
the PCM. This information is stored in non-volatile memory (NVM) in the PCM. It is not cleared when the keep alive memory (KAM) is reset.
Neutral profile learning is accomplished using the scan tool any time a PCM is replaced. It should also be relearned any time the CKP sensor is
replaced or major engine repairs have been completed.
To determine if the neutral profile learning has been completed, check the MP_LRN parameter identification (PID) using the scan tool. The PID
should read YES if the neutral profile learning has been completed. If the PID reads NO, complete the neutral profile learning prior to diagnosing any
misfire DTCs.
Programming the VID Block for a Replacement PCM
The VID block on a replacement PCM is blank and requires programming. There are two procedures available. The first is an automatic data transfer
from the old PCM to the new PCM, the second is manual data entry into the new PCM.
Automatic data transfer is carried out if the old PCM is capable of communicating. This is done by using a scan tool to retrieve data from the old PCM
before removing it from the vehicle. The stored data can be downloaded to the new PCM after it has been installed.
Carry out manual data entry if the old PCM is damaged or incapable of communicating. Remove and install a new PCM. Using a compatible scan tool,
select and carry out the module/parameter programing, referring to the scan tool manufacturer's instruction manual. Make certain that all parameters
are included. Failure to properly program tire size in revolutions per mile, (rev/mile equals 63,360 divided by the tire circumference in inches), axle
ratio, 4x4/4x2, and/or MSOF/ESOF may result in DTCs P1635 and P1639. You may be instructed to contact the As-Built Data Center for the
information needed to manually update the VID block with the scan tool. Contact the center only if the old PCM cannot be used or the data is corrupt.
For Ford and Lincoln Mercury technicians, contact your National Hotline or the Professional Technician Society (PTS) web site for As-Built data
listed under the Service Publications Index. Non-Ford technicians use the Motorcraft(R) website at www.motorcraft.com. From the Motorcraft(R)
home page, use the search function to find the Module Programming or As-Built Data.
For Ford and Lincoln Mercury technicians, check the Programmable Module Installation link on the PTS web site for quick Programmable Module
data information by vehicle.
Making Changes to the VID Block
A programmed PCM may require changes to be made to certain VID information to accommodate the vehicle hardware. Refer to Module
Reprogramming on the scan tool.
Making Changes to the PCM Calibration
At certain times, the EEPROM needs to be completely reprogrammed. This is due to changes made to the strategy or calibration after production or
the need to reset the VID block because it has reached its limit. Refer to PCM/Module Reprogramming on the scan tool.
