K 3500 Truck 4WD V8-6.6L DSL Turbo VIN 1 (2001)
IMPORTANT: DO NOT turn OFF the ignition if the programming procedure is interrupted or unsuccessful. Ensure that all the ECM and DLC
connections are secure and the Techline(TM) operating software is up to date. Attempt to reprogram the control module. If the control module cannot
be programmed, replace the control module. Refer to Engine Control Module (ECM) Replacement.
29. Select Program.
30. After the download is complete, EXIT Service Programming.
31. Turn OFF the ignition for 30 seconds.
32. Turn OFF the Tech 2(TM).
33. If a control module is replaced the following service procedures must be performed:
^
The Engine Oil Life Reset Procedure. Refer to GM Oil Life System - Resetting in Maintenance and Lubrication.
^
Inspection/Maintenance (I/M) Complete System Set Procedure
^
The Vehicle Theft Deterrent Password Learn Procedure. Refer to Programming Theft Deterrent System Components in Theft Deterrent.
Programming Verification
1. With a scan tool, clear the DTCs.
2. Attempt to start the engine.
3. Repeat the Service Programming procedure if the engine does not start or operates poorly. Perform the following procedures before programming
the PCM:
^
Ensure the control module and DLC connections are OK.
^
Ensure the Techline(TM) operating software is up to date.
^
Ensure the calibration part number is correct for the vehicle.
4. Attempt to program the control module. If the control module still cannot be programmed properly, replace the control module. Refer to Engine
Control Module (ECM) Replacement. You must program the replacement control module.
Before Programming A Control Module
IMPORTANT:
^
Do NOT program a control module unless you are directed by a service procedure or you are directed by a General Motors Corporation service
bulletin. Programming a control module at any other time will not permanently correct a customer's concern.
^
The Off-Board Programming is used in situations where a control module must be programmed without having the vehicle present. The Off-Board
Programming Adapter must be used to perform the Off-Board Programming procedure. The adapter allows the control module to power up and
allows the Tech 2(TM) to communicate with the control module.
^
DO NOT disturb the tool harnesses while programming. If an interruption occurs during the programming procedure, programming failure or
control module damage may occur.
Ensure that all connections are secure at the following locations:
^
The Off-Board Programming Adapter
^
The Tech 2(TM)
^
The control module
^
The Techline(TM) terminal
Off-Board Programming
1. Obtain the VIN of the vehicle for which the control module is being programmed.
2. With the Techline(TM) terminal, select Service Programming.
3. Select Tech 2(TM), Reprogram ECU, and Off-Board Programming Adapter as the ECU location.
4. Connect the control module, Off-Board Programming Adapter, and the Tech 2(TM) as described on the Techline(TM) terminal. Ensure you use
the correct harness connector from the Off-Board Programming Adapter kit.
5. With the Tech 2(TM), select Service Programming Request Information function. The Tech 2(TM) communicates with the control module and
receives the access code.
6. With the Tech 2(TM), exit the Service Programming Request Information.
7. Disconnect the Tech 2(TM) from the Off-Board Programming Adapter.
8. Connect the Tech 2(TM) to the Techline(TM) terminal.
9. Turn ON the Tech 2(TM)
10. With the Techline(TM) terminal, enter the VIN of the vehicle that will be receiving the control module.
11. The Techline(TM) terminal will display the message, attaching to database.
12. Identify what type of programming that you are performing.
13. Select the appropriate calibration file.
14. Ensure all connections are secure.
15. The Techline(TM) terminal displays a summary screen that summarizes your selections. After confirming you choices, the Techline(TM) terminal
automatically loads the calibration files to the Tech 2(TM).
16. After the download is complete, turn OFF the Tech 2(TM).
17. Disconnect the Tech 2(TM) from the Techline(TM) terminal.
18. Connect the Tech 2(TM) to the Off-Board Programming Adapter.
19. With the Tech 2(TM), select Service Programming.
