K 3500 Truck 4WD V8-6.6L DSL Turbo VIN 1 (2001)
when the BCM allows the passenger door unlock relay to go to ground to UNLOCK the passenger door(s). The BCM will command this state when the
UNLOCK button on the keyless entry transmitter is activated twice within 3 seconds.
PUDDLE LAMP RELAY: The scan tool displays the commanded state of the puddle lamp relay. The scan tool displays ON when the BCM allows the
puddle lamp relay to go to ground to activate the puddle lamps.
REAR FOG LAMP RELAY: The scan tool displays the commanded state of the rear fog lamp relay. The scan tool displays ON when the BCM allows
the rear fog lamp relay to go to ground to activate the rear fog lamps (Export Only).
RETAINED ACCESSORY POWER (RAP) RELAY: The scan tool displays the commanded state of the RAP relay. The scan tool displays ON when
the BCM allows the RAP relay to go to ground. The BCM will allow operation of the radio and the power windows with the ignition OFF and the doors
closed for up to 1198 seconds (approximately 20 minutes).
Security Data
AUTO LEARN TIMER: The scan tool displays the seconds used by the BCM to learn valid code from the Passlock(TM) sensor. The learn procedure
consists of 3 consecutive periods.
BATTERY VOLTAGE: The scan tool displays the battery system voltage.
CONTENT THEFT LAMP: The scan tool displays the state of the SECURITY lamp. The scan tool displays ON when activated by an unauthorized
entry.
CONTENT THEFT STATE: The scan tool displays the state of the content theft feature. The scan tool displays ALARM when activated by an
unauthorized entry.
DOOR KEY SWITCH: The scan tool displays the state of the door key switch. The scan tool displays ACTIVE when the switch is activated in either
door key cylinder.
IGNITION 1: The scan tool displays the state of the ignition switch. The scan tool displays ACTIVE when the ignition switch is in the RUN or
CRANK position.
IGNITION 3: The scan tool displays the state of the ignition switch. The scan tool displays ACTIVE when the ignition switch is in the RUN position.
PASSLOCK(TM) CODE: The scan tool displays the validity of the Passlock(TM) code received by the BCM. The scan tool displays OPEN,
SHORTED, TAMPER and a valid code as a numeric value (1-10).
PASSLOCK(TM) DATA VOLTAGE: The scan tool displays the voltage code from the Passlock(TM) sensor to the BCM. The BCM determines if
the voltage received is a valid or invalid code voltage.
PASSLOCK(TM) STATE: The scan tool displays the state of the Passlock(TM) system.
SECURITY LAMP STATE: The scan tool displays the state of the SECURITY lamp. The scan tool displays ON, OFF or FLASHING.
TAMPER TIMER: The scan tool displays the time remaining when in the tamper mode. The timer starts when the ignition switch is turned to the RUN
position and the BCM receives a Passlock(TM) data voltage different from the last learned voltage. The timer has a delay of 10 minutes and will stay
active even if the ignition switch is cycled from the RUN to the OFF position.
PCM FAIL ENABLE: The scan tool displays the state of the PCM fail enable mode. The scan tool displays YES when the Passlock(TM) system
transitions from the Monitor Passlock(TM) Data state to the PCM Fail Enable state.
VCM/PCM FUEL CONTINUE: The scan tool displays the state of the PCM fuel continue mode. The scan tool displays YES when the Passlock(TM)
system verifies a valid password to the BCM.
VCM/PCM LEARN TIMER: The scan tool displays the state of the PCM learn timer. The scan tool displays INACTIVE when the BCM is not in a
learn mode.
VTD FUEL DISABLE: The scan tool displays the state of the VTD fuel disable mode. The scan tool displays INACTIVE when the Passlock(TM)
system verifies a valid password.
VTD FUEL DISABLE UNTIL IGNITION OFF: The scan tool displays the state of the VTD fuel disable until Ignition off mode. The scan tool
displays NO when the Passlock(TM) system verifies a valid password.
VTD PASSWORD LEARN MODE: The scan tool displays the state of the VTD password learn mode. The scan tool displays INACTIVE when the
Passlock(TM) system is not in a learn mode.
