S15/T15 Sonoma P/U 2WD L4-2.2L VIN 5 Flex Fuel (2001)
senses that the passenger door unlock relay is being energized.
Remote Function Actuation (RFA) Message Since Wake-Up: The scan tool displays the last message sent to the BCM from the remote control door
lock receiver.
Retained Accessory Power (RAP) Relay Feedback: The scan tool displays the state of the RAP relay. The scan tool displays ON when the BCM
activates the RAP relay.
Seatbelt Buckled: The scan tool displays the position of the drivers seatbelt buckle. The scan tool displays YES when the drivers seatbelt is buckled.
The BCM uses this data in controlling the operation of the seatbelt warning chime and the seatbelt indicator.
Input 2
Auto Headlamps: The scan tool displays the status of the auto headlamps. The scan tool displays ACTIVE when the auto headlamps are ON.
Courtesy Lamp Relay: The scan tool displays the state of the courtesy lamp relay. The scan tool displays ON when the BCM commands the courtesy
lamps ON by providing a ground for the courtesy lamp relay.
Dimming Potentiometer Input: The scan tool displays the position of the dome lamp switch (thumb wheel) when the park lamps are ON. The scan tool
displays ACTIVE when the dome lamp switch is in its normal position and the park lamps are ON.
Dome Lamp Switch: The scan tool displays the position of the dome lamp switch. The scan tool displays ON when the dome lamp switch is to its full
up position past the detent.
Dome Override Switch: The scan tool displays the position of the dome override switch. The scan tool displays ON when the switch is activated and
requesting the BCM to override the interior lighting.
Flash to Pass Switch: The scan tool displays the position of the flash to pass switch. The scan tool displays ON when the switch is pulled to activate the
high beams momentarily while the switch is held.
Headlamp Relay Feedback: The scan tool displays the state of the headlamps. The scan tool displays ON when the headlamp and panel dimmer switch
is manually turned to the ON position. The scan tool also displays ON when the switch is in the AUTO position and the ambient light sensor is in its
DARK state.
High Beam Switch: The scan tool displays the position of the high beam switch. The scan tool displays ON when the high beam switch is activated.
Left Turn Signal: The scan tool displays the position of the turn signal switch. The scan tool displays ON when the left turn signal is activated. The
BCM uses this data to activate the turn signal reminder chime after the vehicle has traveled 0.75 miles with the turn signal switch activated.
Park Lamps: The scan tool displays the state of the park lamps. The scan tool displays ON when the park lamps are activated by the BCM or the
headlamp switch.
Right Turn Signal: The scan tool displays the position of the turn signal switch. The scan tool displays ON when the right turn signal is activated. The
BCM uses this data to activate the turn signal reminder chime after the vehicle has traveled 0.75 miles/1.2 kilometers with the turn signal switch
activated.
Transmission Preference: The scan tool displays the position of the Tow/Haul (transmission preference) switch. The scan tool displays ON when the
switch is activated. The BCM uses this data to illuminate the Tow/Haul indicator on the cluster. When activated the BCM also sends a Class 2 message
to the PCM/VCM which handles the shift control.
Module Information 1
Julian Date of Build: The scan tool displays the date upon which the Body Control Module (BCM) was manufactured.
Manufacture Enable Counter (MEC): The scan tool displays the actual value for the MEC in the BCM. This information is for the assembly plant
only.
Module Part Number: The scan tool displays the part number assigned to the BCM that is currently in the vehicle.
Software Design Suffix: The scan tool displays the version of the software part number in the BCM.
Software Part Number: The scan tool displays the software identification number (ID) in the BCM.
Module Information 2
Lighting Calibration Number: The scan tool displays the lighting configuration calibration part number in the BCM.
Lighting Suffix: The scan tool displays the lighting configuration identification number in the BCM.
Reminder Calibration Number: The scan tool displays the reminder warning calibration part number in the BCM.
