Savana 3500 V8-6.6L DSL Turbo VIN 2 (2006)
Fuel Injector: Testing and Inspection
Fuel Injector Balance Test With Tech 2 (Manual Transmission)
FUEL INJECTOR BALANCE TEST WITH TECH 2 (MANUAL TRANSMISSION)
DIAGNOSTIC FAULT INFORMATION
IMPORTANT: Always perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. See: Computers and Control
Systems/Testing and Inspection/Diagnostic Trouble Code Tests and Associated Procedures
CIRCUIT/SYSTEM DESCRIPTION
The fuel injector balance test is performed when a misfire, knock, excessive smoke, or rough running condition exists with no electrical DTCs. This
test uses the Balance Rate and Cylinder Power Balance test to identify cylinders that are not producing the designed power output. The balance rate
adjustments are utilized by the engine control module (ECM) only at idle. The balance rates are the fuel adjustments for each individual cylinder
based on the variations in engine crankshaft speed. The balance rates will change depending on if the transmission is in Neutral or Drive. During the
Cylinder Power Balance portion of the test, the ECM turns OFF individual injectors while the engine is running. The ECM adjusts for the drop in
engine RPM during cancellation and may not change on the scan tool display. The lack of power at the cancelled cylinder will feel like a misfiring
cylinder or vibration. If a fuel injector is turned OFF and there is a no difference felt when compared to the other cylinders, that cylinder is identified
with the concern. If the customer concern occurs during idle or during off-idle tip in acceleration, the balance rates are used to identify the cylinder
with a fault related to the fuel injector or engine compression.
DIAGNOSTIC AIDS
If the majority of the balance rates are positive and high, the dual-mass flywheel is causing a harmonic vibration that is affecting the engine fuel
control system.
A dual mass flywheel concern will cause the balance rates to be inaccurate. The transmission concerns must be repaired before any fuel system
diagnostic can be performed.
The Cylinder Power Balance Test may be performed at any engine speed or load from idle to wide open throttle (WOT). There is a 5-minute time
limit for each test.
A high balance rate may be caused by a fuel injector or compression only if the ECM can control fuel pressure.
CIRCUIT/SYSTEM VERIFICATION
Observe the Balancing Rate parameters with a scan tool. Normal reading should be between +4 cu.mm and -4 cu.mm at idle. With the engine running
at idle, the Actual Fuel Rail Pressure should be close to the Desired Fuel Rail Pressure.
CIRCUIT/SYSTEM TESTING
If any DTCs other than DTC P0300, P0301-P0308 are set, refer to Diagnostic Trouble Code (DTC) List - Vehicle. See: Computers and Control
Systems/Testing and Inspection/Diagnostic Trouble Code Descriptions
1. Start and run the engine until the ECT is more than 82°C (180°F).
2. Turn OFF all accessories.
3. Perform the fuel pressure regulator test. Refer to Fuel Pressure Regulator Diagnosis.
-
If the fuel pressure regulator graph was not normal, replace the fuel pressure regulator Fuel Pressure Regulator Replacement. See: Computers
and Control Systems/Testing and Inspection/Component Tests and General Diagnostics/Fuel Pressure Regulator Diagnosis
4. Place the transmission in Neutral and apply the parking brake.
5. Hold the brake pedal in the fully applied position. A hiss will be noticeable when the brake is fully applied.
6. Idle the engine for more than 30 seconds.
7. Record the Balancing Rate Cyl.1-8 parameters from the scan tool while the engine is at idle speed.
-
If at least 5 of the Balancing Rates are more than +4 cu.mm, refer to Engine Flywheel Replacement.
-
If the Balance Rates are not between +4 cu.mm and -4 cu.mm at idle, perform the Cylinder Power Balance Test in Special Functions.
8. Record any cylinders that indicate a different cylinder power contribution and compare the Balance Rates previously recorded with the Cylinder
Power Balance results.
-
If the Balance Rates were not high or the Cylinder Power Balance test did not indicated a cylinder with a different power contribution, refer to
Diagnostic Aids.
IMPORTANT: The Cylinder Power Balance Test must be performed under the conditions for which the concern occurred. The concern must be
duplicated during the test.
9. Perform the engine compression test. Refer to Engine Compression Test.
-
If the compression test indicated any of the cylinder had low compression, refer to Symptoms - Engine. See: Tune-up and Engine Performance
Checks/Compression Check/Testing and Inspection See: Engine, Cooling and Exhaust/Engine/Testing and Inspection/Symptom Related
Diagnostic Procedures
IMPORTANT: A fuel injector leak into the combustion chamber may result in mechanical damage to the cylinder. If any fuel spray comes out of a
