Yukon Denali 2WD V8-6.0L Hybrid (2010)
CCSM.
‹› If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the CCSM.
Note: The ignition must be cycled OFF then ON between each test in order to reset the CCSM.
14. Ignition OFF then ON, connect a test lamp between the control circuit terminals listed below and ground. Press the HEAT switch when testing the
heat control circuit and the COOL switch when testing the cool control circuit. The test lamp should illuminate or slowly illuminate for
approximately 4 seconds after the switch is pressed. On the heat control circuit, the test lamp may exhibit a 4 second delay before it starts to
illuminate.
*
Seat back heat control circuit terminal 1
*
Seat back cool control circuit terminal 3
‹› If the test lamp does not illuminate, test the appropriate control circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the CCSM.
‹› If the test lamp is always ON, test the appropriate control circuit for a short to voltage. If the circuit tests normal, replace the CCSM.
Note: The ignition must be cycled OFF then ON between each test in order to reset the CCSM.
15. Ignition OFF then ON, connect a test lamp between the circuit terminals listed below and ground. The test lamp should illuminate or slowly
illuminate for approximately 5 seconds after pressing the HEAT switch.
*
Seat back blower control circuit terminal 2
*
Seat cushion blower speed control circuit terminal 7
‹› If the test lamp does not illuminate, test the appropriate control circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the CCSM.
‹› If the test lamp is always ON, test the appropriate control circuit for a short to voltage. If the circuit tests normal, replace the CCSM.
16. If all circuits test normal, test or replace the appropriate seat cushion or seat back ventilation heating and cooling module.
Passenger Heated/Cool Seat Circuit System Testing
1. Ignition OFF, disconnect the X3 harness connector at the CCSM.
2. Connect a test lamp between the signal circuit terminal 6 and B+.
3. Ignition ON, press the HEAT or COOL seat switch through the high, medium, and low positions to OFF. The test lamp should illuminate until the
OFF position is reached.
‹› If the test lamp does not illuminate, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace
the MSM.
‹› If the test lamp remains ON with the switch in the OFF position, test the signal circuit for a short to ground. If the circuit tests normal, replace
the MSM.
4. Connect the X3 harness connector at the CCSM.
5. Disconnect the harness connector at the seat cushion ventilation heating and cooling module.
6. Test for less than 5 Ohms between the low reference circuit terminal 4 and ground.
‹› If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the CCSM.
7. Ignition ON, test for 4.8 - 5.2 V between the signal circuit terminal 5 and ground.
‹› If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
CCSM.
‹› If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the CCSM.
Note: The ignition must be cycled OFF then ON between each test in order to reset the CCSM.
8. Ignition OFF then ON, connect a test lamp between the control circuit terminals listed below and ground. Press the HEAT switch when testing the
heat control circuit and the COOL switch when testing the cool control circuit. The test lamp should illuminate or slowly illuminate for
approximately 2 - 4 seconds after the switch is pressed. On the heat control circuit, the test lamp may exhibit a 4 second delay before it starts to
illuminate.
*
Seat cushion heat control circuit terminal 1
*
Seat cushion cool control circuit terminal 3
‹› If the test lamp does not illuminate, test the appropriate control circuit for a short to ground or an open/high resistance. If the circuit tests
normal, replace the CCSM.
