Yukon Denali 4WD V8-6.0L Hybrid (2011)
Garage Door Opener Transmitter: Programming and Relearning
Garage Door Opener Programming - Universal
Important: Do not use the garage door opener (GDO) with any garage door opener that does not have the stop and reverse safety feature. This
includes any garage door opener model manufactured before April 1, 1982.
Ensure that people and objects are clear of the garage door while performing programming operations.
Programming the GDO for Rolling Code Receivers
Important: If the programming procedure is unsuccessful, it may be necessary to perform the Erasing Channels procedure first.
This procedure will learn a rolling code garage door opener to the GDO transmitter. The learn process must be completed within 30 seconds.
1. Press the two outside buttons of the GDO for one to two seconds, then immediately release them.
2. Locate the "Learn" or "Smart" button on the garage door opener receiver (located on the garage door opener motor-head unit). It is often found
where the hanging antenna wire is attached to the motor-head unit and may be a colored button. Refer to the garage door opener operator's manual
or call 1-866-572-2728 for assistance. Press the "Learn" or "Smart" button. The garage door opener operator's manual may provide assistance in
determining when the unit is in learn mode.
3. Immediately return to the GDO transmitter in the vehicle. Press and hold the button that is to be learned; the LED above the button will begin to
flash slowly. When the garage door moves, immediately release the button. The LED will flash rapidly until programming is complete.
4. Press the button used during the learn operation again in order to verify that the GDO transmitter has been programmed.
The GDO is compatible with most, but not all, types of garage door openers. If the GDO LED does not flash rapidly after 90 seconds, there may be a
compatibility conflict with the garage door opener. Call 1-866-572-2728 to address compatibility concerns.
Programming the GDO for Fixed Code Receivers
Important: If the programming procedure is unsuccessful, it may be necessary to perform the Erasing Channels procedure first.
This procedure will learn a fixed code garage door opener to the GDO transmitter. To determine if the customer has a fixed code garage door opener,
remove the battery cover on the customer supplied transmitter. If a row of dip switches is present, the garage door opener is a fixed code version. The
transmitter should have anywhere from 8 to 12 switches. The garage door opener receiver may also have a set of dip switches. If the number of switches
on the receiver and the transmitter do not match, use the receiver switches to program the GDO. Each dip switch may have either two or three positions.
The two position switch can either be ON or OFF. The three position switch can either be ON, NEUTRAL, or OFF.
1. Write down the positions of the dip switches. The positions of the switches will be entered from left to right into the GDO using the three buttons.
2. Press all three buttons on the GDO for three seconds and immediately release them. The LEDs should flash slowly, indicating that the GDO is in
programming mode.
3. Enter the positions of the dip switches one at a time. If a position of a dip switch is on, press the left button on the GDO. If the position is neutral,
press the middle button of the GDO. If the position is off, press the right button of the GDO. Enter all of the positions of the dip switches. The
procedure must be completed in two and a half minutes.
4. After entering all of the switch positions, firmly press and release all three buttons at the same time. The indicator lights will turn on.
5. Press and hold the button that is to be learned; the LED above the button will begin to flash slowly. When the garage door moves, immediately
release the button. The LED will flash rapidly until programming is complete.
6. Press the button used during the learn operation again in order to verify that the GDO transmitter has been programmed.
The GDO is compatible with most, but not all, types of garage door openers. If the GDO light does not flash rapidly after 90 seconds, there may be a
compatibility conflict with the garage door opener. Call 1-866-572-2728 to address compatibility concerns.
Erasing Channels
To erase programmed channels, press and hold the two outside buttons until the lights on the GDO transmitter begins to flash. Once the LEDs begin to
flash, release both buttons; all learned codes are now erased.
Individual channels cannot be erased, but can be reprogrammed using the procedures above.
