Veracruz FWD V6-3.8L (2009)
Body Control Module: Description and Operation
Assist Door Module (ADM)
Description
The POWER WINDOW ASSIST SWITCH ASSY shall be one component of the CAN SYSTEM. The SWITCH ASSY POWER WINDOW ASSIST
shall communicate through CAN with the BCM, the SEAT ECU, the TILT ECU, the SWITCH ASSY POWER WINDOW MAIN.
1. POWER WINDOW OPERATION BY BUTTON
The SIDE P/WMW BUTTON shall output signal to the 2 operations of the Manual UP/DOWN
2. PASSIVE Operation OF MIRROR'S POSITION BY MANUAL SW (UP, DOWN, LEFT, RIGHT)
THE RECEIPT FROM P/WDW MAIN SW WITH CAN COMMUNICATION
3. THE MEMORY AND REMINDING Operation FOR POSITIONING THE MIRROR USING MEMORY SWITCH(FOR 2 PASSENGERS)
THE RECEIPT FROM P/WDW MAIN SW WITH CAN COMMUNICATION
4. RECEIPT BY CENTRAL DOOR LOCK/UNLOCK BUTTON Operation WITH CAN COMMUNICATION
5. CONTAINMENT AND RETURN FUNCTION OF OUTSIDE MIRROR
Control Function
1. POWER WINDOW CONTROL
(1) POWER WINDOW OPERATING CONDITION
A. POWER WINDOW LOCK SW(FROM DDM) OFF & POWER WINDOW TIMER(FROM BCM) ON or IGN2(ADM) ON
(2) POWER WINDOW UP/DOWN OPERATING
A. Receiving P/WDW UP/DOWN (FROM DDM or ADM itself) signal input under POWER WINDOW drive condition, Run assist's
POWER WINDOW. Can not be outputted more than 15 seconds by same one-way only.
2. OUTSIDE MIRROR Control Control BY MANUAL SWITCH
(1) ASSIST SIDE OUTSIDE MIRROR OPERATION
A. The ACC ON state, if the mirror select switch in DDM is the RH state and the mirror direction switches (UP, DOWN, LEFT, and RIGHT)
are operated, then the mirror motor shall be drive to control the mirror to the desired direction by receiving CAN msg. At this time,
Up/Down direction conversion or Right/Left direction conversion, it have 100 ms Delay Times.
3. OUTSIDE MIRROR MEMORY OPERATION BY MEMORY SWITCH
(1) AFTER RECEPTION FROM THE P/WDW MAIN SW WITH CAN COMMUNICATION, MEMORIZE ASSIST SIDE O/S MIRROR
position.
Except, when the mirror manual switch at the RH is operated, the mirror position at RH shall not be memorized.
(2) WHEN GETTING RID OF BATTERY, SAVE THE MIRROR position position MEMORIZED BY MEMORY SWITCH TO EEPROM.
4. OUTSIDE MIRROR REMINDING OPERATION BY MEMORY SWITCH
(1) Drive MIRROR reminding to position that is remembered if receive MIRROR reminding request (CAN) from DDM in IGN2 ON state.
(2) Reminding operation of position that is not remembered is not operation.
(3) It act reminding to position that is required lastly if it receive reminding request (FROM DDM) of different position during reminding
operation.
(4) Reminding prohibition condition
A. INHIBIT "P" SW(FROM IMS) is OFF
B. IGN2 OFF
C. RH side MIRROR MANUAL SW's manufacturing (FROM DDM) is occurred
D. vehicle speed is more than 3 Km/h (FROM BCM)
5. OUTSIDE MIRROR FAIL SAFE FUNCTION
(1) If the sensor variation of 80㎷ and more is not occurred even there is an input variation from the position sensor when motor is driven, it shall
be considered as occurring defects such as the harness disconnection, the motor failure, or the sensor malfunction so that the auto control
operation should be quitted.
(2) The mirror driving signal should not output over 15 seconds continuously. (Both the memory reminding and the manual switching operation)
(3) Monitoring the Reminding Operation Time. If the reminding operation does not complete within 40 seconds after starting, the output of the
mirror motor should be quitted and the reminding operation should be finished.
6. OUTSIDE MIRROR DOWN OPERATION AT REVERSING (AUTO REVERSE)
