Oasis LS L4-2156cc 2.2L SOHC MFI F22B6 (1997)
1. If installed in a vehicle, follow the removal procedure on page 24-46.
2. In all cases, make a short circuit by twisting together the two airbag inflator wires.
3. Package the airbag in exactly the same packaging that the new replacement part came in.
4. Mark the outside of the box "DAMAGED AIRBAG NOT DEPLOYED" so it does not get confused with your parts stock.
5. Contact your Honda District Service Manager for how and where to return it for disposal.
Deployment Tool: Check Procedure
1. Connect the yellow clips to both switch protector handles on the tool; connect the tool to a battery,
2. Push the operation switch: green means the tool is OK; red means the tool is faulty.
3. Disconnect the battery and the yellow clips.
Deployed Air Bag Handling
When handling a deployed air bag assembly, a face shield and rubber gloves should be worn. Vehicle interior and A/C, vent, defroster and heater ducts
should be vacuumed. If sinus or throat irritation is encountered during air bag removal, exit vehicle and breathe fresh air. If skin irritation is encountered,
flush effected area with cool water. If sinus, throat, skin or any other type of irritation continues, consult a physician. After handling a deployed air bag
assembly, wash hands and rinse thoroughly with water.
An air bag that has been deployed should be removed from the vehicle. Prior to removing a deployed air bag assembly, place tape over air bag exhaust
vents. After unit has been removed, it should be placed in a heavy duty plastic bag and sealed securely. The sealed plastic bag should then be placed with
automotive scrap. An air bag assembly that has not been deployed, must be deployed prior to disposal.
Put on a pair of shop gloves and safety glasses to protect your hands and eyes from possible irritation and heat when handling the deployed air bag
assembly.
After the air bag assembly has been deployed, the surface of the air bag may contain a powdery residue. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and by products of the chemical reaction. Sodium hydroxide dust (similar to lye soap) is produced as a by product
of the deployment reaction. The sodium hydroxide then quickly reacts with atmospheric moisture and is converted to sodium carbonate and sodium
bicarbonate (baking soda).
Driver Airbag Assembly
After the air bag assembly has been deployed, the surface of the air bag may contain a powdery residue. This powder consists primarily of cornstarch
(used to lubricate the bag as it inflates) and by products of the chemical reaction. Sodium hydroxide dust (similar to lye soap) is produced as a by product
of the deployment reaction. The sodium hydroxide then quickly reacts with atmospheric moisture and is converted to sodium carbonate and sodium
bicarbonate (baking soda). Therefore, it is unlikely that sodium hydroxide will be present after deployment.
Passenger Airbag Assembly
The passenger inflator requires no special precaution after deployment. 95% of the particulate emission are potassium chloride (KCL), which is
commonly sold as an edible salt-substitutes. even if water is applied. Post deployment products are relatively pH neutral. Disposing the inflator by
burying it in a landfill will not products any hazardous products. As with any dusty environment, safety goggles, dust mask and gloves should be worn.
Damaged Airbag/Tensioner Special Procedure
WARNING: If an airbag (or Seat Belt Tensioner) cannot be deployed, it should not be treated as normal scrap; it should still be considered a
potentially explosive device that can cause serious injury.
Special Procedure For Damaged Airbag
1. If installed in a vehicle, follow the removal procedure.
2. In all cases, make a short circuit by twisting together the two airbag inflator wires.
3. Package the airbag in exactly the same packaging that the new replacement part came in.
4. Mark the outside of the box "DAMAGED AIRBAG (or TENSIONER) NOT DEPLOYED" so it does not get confused with your parts stock.
5. Contact your Isuzu District Service Manager for how and where to return it for disposal.
Removal and Installation
After a collision in which the airbags were deployed, the airbag assemblies and the SRS unit must be replaced.
WARNING: Store a removed airbag assembly with the pad surface up. If the airbag is improperly stored face down, accidental deployment
could propel the unit with enough force to cause serious injury.
CAUTION:
^
Do not install used SRS parts from another vehicle. When repairing, use only new SRS parts.
^
Carefully inspect the airbag assembly before you install it. Do not install an airbag assembly that shows signs of being dropped or improperly
handled, such as dents, cracks or deformation.
