Commander 4WD V8-4.7L Flex Fuel (2009)
Brake Warning Indicator: Description and Operation
Brake/Parking Brake Indicator - Operation
OPERATION
The brake indicator gives an indication to the vehicle operator when the parking brake is applied, when there are certain brake hydraulic system
malfunctions as indicated by a low brake hydraulic fluid level condition, or when the brake fluid level switch is disconnected. The brake indicator can
also give an indication when certain faults are detected in the Antilock Brake System (ABS). This indicator is controlled by a transistor on the instrument
cluster circuit board based upon cluster programming, electronic messages received by the cluster from the Controller Antilock Brake (CAB) over the
Controller Area Network (CAN) data bus, and a hard wired input from the park brake switch.
The brake indicator Light Emitting Diode (LED) is completely controlled by the instrument cluster logic circuit, and that logic will only allow this
indicator to operate when the instrument cluster receives a battery current input on the fused ignition switch output (run-start) circuit. Therefore, the LED
will always be OFF when the ignition switch is in any position except ON or START. The LED only illuminates when it is provided a path to ground by
the instrument cluster transistor. The instrument cluster will turn ON the brake indicator for the following reasons:
-
Bulb Test - Each time the ignition switch is turned to the ON position the brake indicator is illuminated by the instrument cluster for about three
seconds as a bulb test.
-
Brake Indicator Lamp-On Message - Each time the cluster receives an electronic brake indicator lamp-ON message from the CAB, the brake
indicator will be illuminated. The CAB may also send lamp-ON messages as feedback during ABS diagnostic procedures. The indicator remains
illuminated until the cluster receives a lamp-OFF message from the CAB, or until the ignition switch is turned to the OFF position, whichever
occurs first.
-
Low Brake Fluid Textual Warning Message - When the CAB detects a low brake fluid level input from the brake fluid level switch, it will send
an electronic textual warning request message requesting the cluster display a textual warning message. Each time the cluster receives this
message from the CAB, a LOW BRAKE FLUID LEVEL textual message will appear within the cluster reconfigurable dot matrix display to
accompany brake indicator illumination. This message indicates that the CAB has detected a low brake fluid level condition in the brake master
cylinder or that there is a problem in the brake fluid level switch or circuits.
-
Park Brake Switch Input - Each time the cluster detects ground on the park brake switch sense circuit (park brake switch closed = park brake
applied or not fully released) while the ignition switch is in the ON position, the brake indicator flashes ON and OFF. The indicator continues to
flash until the park brake switch sense input to the cluster is an open circuit (park brake switch open = park brake fully released), or until the
ignition switch is turned to the OFF position, whichever occurs first.
-
Antilock Brake System (ABS) Indicator Backup - If the instrument cluster detects a fault in the ABS indicator circuit it will send a message
indicating the fault to the Controller Antilock Brake (CAB), then flash the brake indicator ON and OFF. The cluster will continue to flash the
brake indicator until the ABS indicator circuit fault is resolved, or until the ignition switch is turned to the OFF position, whichever occurs first.
-
Self Test - Each time the instrument cluster is put through the self test, the brake indicator will be turned ON, then OFF again during the bulb
check portion of the test to confirm the functionality of the LED and the cluster control circuitry.
The park brake switch on the park brake lever mechanism provides a hard wired ground input to the instrument cluster circuitry through the park brake
switch sense circuit whenever the park brake is applied or not fully released. The CAB continually monitors the ABS system circuits and sensors,
including the brake fluid level switch on the brake master cylinder reservoir, to decide whether the system is in good operating condition. The CAB then
sends the proper lamp-ON or lamp-OFF message to the instrument cluster, also known as the Cab Compartment Node (CCN). If the CAB sends a
lamp-ON message after the bulb test, it indicates that the CAB has detected a brake hydraulic system malfunction or that the ABS system has become
ineffective. The CAB will store a Diagnostic Trouble Code (DTC) for any malfunction it detects.
The hard wired park brake switch input to the instrument cluster may be diagnosed using conventional diagnostic tools and procedures. Refer to the
appropriate wiring information. For proper diagnosis of the brake fluid level switch, the ABS, the CAB, the CCN, the CAN data bus or the electronic
communication related to brake indicator operation a diagnostic scan tool is required. Refer to the appropriate diagnostic information.
