jeep Workshop Repair Guides

Jeep Workshop Service and Repair Manuals

Description - Door Ajar Switch|Page 871 > < Description - Door Ajar Switch|Page 869
Page 1
background image

Door Switch: Description and Operation

Description - Door Ajar Switch

DOOR

This vehicle has one door ajar switch for each door. Each switch is concealed within and integral to its respective door latch unit. The switches are
momentary leaf contact-type units that are actuated by the mechanisms internal to the door latch. A short pigtail wire and connector on each door latch
connects the door ajar switch to the vehicle electrical system through its respective door wire harness.

The door ajar switches cannot be adjusted or repaired and, if ineffective or damaged, the door latch unit must be replaced. See: Body and Frame/Doors,
Hood and Trunk/Doors/Front Door/Front Door Latch/Service and Repair/Front Door Latch - Removal or See: Body and Frame/Doors, Hood and
Trunk/Doors/Rear Door/Rear Door Latch/Service and Repair/Rear Door Latch - Removal.

Description - Flip-Up Glass Ajar Switch

FLIP-UP GLASS

A liftgate flip-up glass ajar switch is standard equipment on this vehicle. The switch is concealed within and integral to the liftgate flip-up glass latch
unit. The switch is a momentary leaf contact-type unit that is actuated by the flip-up glass latch mechanism. An integral connector receptacle on the
flip-up glass latch connects the ajar switch to the vehicle electrical system through the liftgate wire harness.

The flip-up glass ajar switch cannot be adjusted or repaired and, if ineffective or damaged, the flip-up glass latch unit must be replaced. See: Body and
Frame/Doors, Hood and Trunk/Trunk / Liftgate/Trunk / Liftgate Latch/Service and Repair/Flipper Glass Latch/Removal.

Description - Liftgate Ajar Switch

LIFTGATE

A liftgate ajar switch is standard equipment on this vehicle. The switch is concealed within and integral to the liftgate latch unit. The switch is a
momentary leaf contact-type unit that is actuated by the liftgate latch mechanism. An integral connector receptacle on the liftgate latch connects the
liftgate ajar switch to the vehicle electrical system through the liftgate wire harness.

The liftgate ajar switch cannot be adjusted or repaired and, if ineffective or damaged, the liftgate latch unit must be replaced. See: Body and
Frame/Doors, Hood and Trunk/Trunk / Liftgate/Trunk / Liftgate Latch/Service and Repair/Liftgate Latch - Removal.

Operation - Door Ajar Switch

DOOR

The door ajar switches are actuated by the mechanisms internal to the door latch. When a door is closed and properly latched, its door ajar switch is an
open circuit. When a door is open or only partially latched, the door ajar switch is a closed circuit. The door ajar switches are hard wired in series
between a body ground and the Totally Integrated Power Module (TIPM). The TIPM reads the hard wired door ajar switch inputs through internal
pull-ups, then uses these inputs to control many electronic functions and features of the vehicle. The TIPM also sends electronic door ajar switch status
messages over the Controller Area Network (CAN) data bus.

The door ajar switches as well as the hard wired inputs and outputs of the switches may be diagnosed using conventional diagnostic tools and
procedures. Refer to the appropriate wiring information.

Operation - Flip-Up Glass Ajar Switch

FLIP-UP GLASS

The liftgate flip-up glass ajar switch is actuated by the flip-up glass latch mechanism. When the flip-up glass is closed and properly latched, its ajar
switch is an open circuit. When the glass is open or only partially latched, the ajar switch is a closed circuit. The flip-up glass ajar switch is hard wired in
series between a body ground and the Totally Integrated Power Module (TIPM). The TIPM reads the hard wired flip-up glass ajar switch input through
an internal pull-up, then uses this input to control many electronic functions and features of the vehicle. The TIPM also sends electronic flip-up glass
ajar switch status
 messages over the Controller Area Network (CAN) data bus.

The flip-up glass ajar switch as well as the hard wired inputs and outputs of the switch may be diagnosed using conventional diagnostic tools and
procedures. Refer to the appropriate wiring information.

Operation - Liftgate Ajar Switch

Description - Door Ajar Switch|Page 871 > < Description - Door Ajar Switch|Page 869