Wrangler 2WD V6-3.8L (2008)
Audible Warning Device: Description and Operation
Operation
OPERATION
The chime warning system operates on battery voltage received through a fuse in the Totally Integrated Power Module (TIPM) on a non-switched fused
B(+) circuit so that the system may operate regardless of the ignition switch position. The chime warning system also monitors the ignition switch
position so that some chime features are functional only with the ignition switch in the ON position, while others are functional regardless of the ignition
switch position.
The chime warning system provides an audible indication to the vehicle operator or occupants under the following conditions:
-
Airbag Indicator Warning - The ElectroMechanical Instrument Cluster (EMIC) (also known as the Cab Compartment Node/CCN) transducer
will generate one short chime when the ignition switch is in the ON position, and the airbag indicator is illuminated. This warning indicates that a
failure condition has been monitored affecting the operation of the Supplemental Restraint System (SRS) related components or circuits. This
warning will only occur following completion of the airbag indicator bulb test, and will only occur once during any ignition cycle.
-
Door Ajar Warning - The EMIC/CCN will generate one short chime when the ignition switch is in the ON position, when the door ajar indicator
is illuminated, or when a DOOR(S) OPEN textual message is displayed in the odometer Vacuum Fluorescent Display (VFD) unit of the
instrument cluster. This warning indicates that a door is, or multiple doors are not closed or completely latched while the vehicle is moving.
-
Fasten Seat Belt Indicator Warning - The EMIC/CCN transducer will generate repetitive chimes at a slow rate to announce that the seat belt
switches and the ignition switch indicate that a front seat belt is not fastened with the ignition switch in the ON position. Vehicles with the optional
Occupant Classification System (OCS) monitor both outboard front seat belts, while vehicles without OCS monitor only the driver side front seat
belt. The chime warning system also supports the enhanced seat belt reminder (beltminder) when this feature is enabled. See: Seat Belt Reminder
Lamp/Description and Operation/Operation.
-
Gate Ajar Indicator Warning - The EMIC/CCN transducer will generate one short chime when the swing gate/trunk ajar indicator is
illuminated, or when a SWING GATE OPEN textual message is displayed in the odometer VFD unit of the instrument cluster. This warning
indicates that the swing gate is not closed or completely latched while the vehicle is moving.
-
Head/Park Lamps-On Warning - The EMIC/CCN transducer will generate repetitive chimes at a fast rate to indicate that inputs from the
headlamp switch and the ignition switch indicate that the exterior lamps are turned ON with the ignition switch in the OFF position, and a hard
wired input is received indicating that the driver side front door is open. The chimes will continue to sound until the exterior lamps are turned
OFF, the driver side front door is closed, or the ignition switch is turned to the ON position, whichever occurs first.
-
Key-In-Ignition Warning - The EMIC/CCN transducer will generate repetitive chimes at a fast rate to indicate that inputs from the key-in
ignition switch, the ignition switch, and the driver side front door ajar switch indicate that the key is in the ignition lock cylinder with the ignition
switch in the OFF position with the driver side front door open. The chimes will continue to sound until the key is removed from the ignition lock
cylinder, the driver side front door is closed, or the ignition switch is turned to the ON position, whichever occurs first.
-
Low Fuel Indicator Warning - The EMIC/CCN transducer will generate one short chime when the low fuel indicator is illuminated in the
instrument cluster. This warning indicates that the monitored fuel level in the fuel tank is low. This chime will only occur once during any ignition
cycle.
-
Park Brake Reminder - The EMIC/CCN transducer will generate one short chime when the brake/park brake indicator is illuminated to
announce that the park brake is applied or not fully released and the vehicle is moving. This chime will repeat each time the input conditions are
met.
-
Overspeed Warning - The EMIC transducer will generate one short chime when the vehicle speed is over a pre-programmed speed value. This
feature is only enabled on vehicles that have been configured for sale in a Middle East Gulf Coast Country (GCC).
-
Park Brake Reminder - The instrument cluster chime tone generator will generate ten repetitive chimes at a slow rate to announce that the hard
wired input from the park brake switch and a vehicle speed message input received from the PCM over the PCI data bus indicates that the park
brake is applied and the vehicle is moving. This chime feature will repeat each time the input conditions are met.
-
Sentry Key Customer Learn Mode Announcement - The EMIC/CCN transducer will generate one short chime to confirm that the Sentry Key
electronic Customer Learn mode is active, which indicates that the Sentry Key Remote Entry Module/Wireless Control Module
(SKREEM/WCM) is prepared for programming additional Sentry Key transponders. This chime feature is only active on vehicles equipped with
the optional Sentry Key system, and sold in a market where Customer Learn programming is an allowed feature.
-
Turn Signal On Warning - The EMIC/CCN transducer will generate repetitive chimes at a slow rate to indicate that a turn signal has been active
continuously for 1.6 kilometers (1 mile) with the vehicle speed greater than 22 kilometers-per-hour (15 miles-per hour). Vehicles built for markets
other than the United States and Canada have a revised distance threshold of 4 kilometers (2.49 miles) for this feature. The chime will continue
until the turn signal input becomes inactive or until the vehicle speed message indicates that the speed is less than 22 kilometers-per-hour (15
miles-per-hour), whichever occurs first. The hazard warning flashers will not activate this chime feature.
-
Warning Indicator Announcement - The EMIC/CCN transducer will generate one short chime each time the Malfunction Indicator Lamp
(MIL) lamp or certain other indicators are illuminated by the instrument cluster circuitry. The MIL and certain other indicators may be illuminated
when any critical engine or transmission systems are operating outside of their normal parameters. The instrument cluster monitors electronic
messages received over the CAN data bus to determine when to illuminate these indicators.
The EMIC/CCN provides chime service for all available features in the chime warning system. The EMIC/CCN relies upon its internal programming,
numerous hard wired inputs, and electronic message inputs received from other modules over the Controller Area Network (CAN) and the Local
Interface Network (LIN) data buses to provide the chime warning system features. The internal programming of the EMIC/CCN determines the priority
of each chime request input that is received, as well as the rate and duration of each chime that is to be generated.
