Rio L4-1.5L (2001)
AIRBAG CAUSE IT TO RICOCHET AND CAUSE PERSONAL INJURY.
8. Verify that green POWER indicator on deployment tool is illuminated.
9. Depress and hold READY button (button number 1).
10. Verify that yellow READY indicator is flashing.
11. Depress and hold DEPLOY button (button number 2).
12. Verify that Air Bag module has deployed. If not, verify that red DEPLOY indicator is illuminated.
13. Release both READY and DEPLOY buttons.
14. Verify that both READY and DEPLOY indicators are no longer illuminated.
15. If air bag successfully deployed, allow a minimum of twenty minutes for bag to cool before handling. Monitor bag throughout cool-down period
to ensure that hot components do not start a fire.
16. If air bag did not deploy, keep area around deployment site clear of personnel for a minimum of 30 minutes.
17. Disconnect the power leads from the battery.
18. Remove the air bag from the stack of tires carefully, wearing rubber gloves and eye/face protection to protect yourself from possible chemical
exposure.
19. Dispose of the complete air bag assembly. No part of the air bag may be reused. Place the air bag into a sturdy plastic bag and seal securely.
Dispose of the deployed air bag according to federal, state and local laws and regulations including, but not limited to, EPA and OSHA
regulations.
20. Install battery.
Air Bag Module (Passenger Side)
WARNING:
A.
FAILURE TO FOLLOW ALL WARNINGS, CAUTIONS, NOTICES AND PROCEDURES COULD RESULT IN PERSONAL INJURY
OR DEATH.
B.
SURFACE OF A DEPLOYED AIRBAG MAY CONTAIN SMALL AMOUNTS OF SODIUM HYDROXIDE(NAOH). PREVENT
CONTACT OF AIRBAG MODULE WITH LIQUIDS, COMBUSTIBLES, AND FLAMMABLE MATERIALS. IMMEDIATELY
WASH HANDS AND EXPOSED SKIN AREAS WITH MILD SOAP AND WATER. FLUSH EYES WITH WATER IF EXPOSED TO
BY PRODUCTS. FAILURE TO FOLLOWING THESE INSTRUCTIONS COULD RESULT IN CHEMICAL BURNS AND
PERSONAL INJURY.
C.
A LIVE(UNDEPLOYED) AIRBAG MODULE MAY ACCIDENTLY DEPLOY DURING HANDLING. WHEN CARRYING A LIVE
AIRBAG MODULE, POINT TRIM COVER AWAY FROM YOUR BODY TO LESSEN CHANCE OF INJURY IN CASE OF
ACCIDENTAL DEPLOYMENT. NEVER CARRY MODULE BY ITS WIRING OR CONNECTORS.
D.
ALWAYS PLACE LIVE AIRBAG MODULES FACE UP TO LESSEN MOTION OF MODULE IN CASE OF ACCIDENTAL
DEPLOYMENT. KEEP AREA CLEAR OF PARTS, TOOLS, AND DEBRIS.
E.
NEVER PLACE ITEMS ON OR ABOVE TRIM COVER OF A LIVE AIRBAG MODULE. IN CASE OF ACCIDENTAL
DEPLOYMENT, SUCH ITEMS MAY CAUSE SERIOUS INJURY OR DEATH.
F.
DAMAGED AIRBAG MODULES SHOULD BE STORED AWAY FROM ALL ACIDS, HALOGENS, HEAVY METALS, AND
METAL SALTS. DAMAGED UNITS MAY PRODUCE HYDROZOIC ACID IF EXPOSED TO LIQUIDS. IF AN UNDEPLOYED
AIRBAG MODULE OR INFLATOR IS RUPTURED OR TAMPERED WITH, REFER TO PARTICULAR MODULE'S
MSDS(MATERIAL SAFETY DATA SHEET) FOR IMPORTANT INFORMATION CONCERNING CONSTITUENTS OF
UNDEPLOYED MODULES. EXPOSURE TO HIGH CONCENTRATIONS OF PROPELLANT MIXTURE CAN CAUSE
HEADACHES, NAUSEA, BLURRED VISION, FAINTNESS, CYANOSIS, LOWERING OF BLOOD PRESSURE OR
TACHYCARDIA. FAILURE TO COMPLY WITH THIS WARNING CAN RESULT IN FIRE, NOXIOUS FUMES, SEVERE
PERSONAL INJURY, OR DEATH.
G.
AIR BAG MODULE COMPONENTS ARE VERY HOT AFTER DEPLOYMENT. UNITS SHOULD BE DEPLOYED OUTDOORS OR
IN AN OPEN AREA TO PREVENT FIRES. ALLOW COMPONENTS AT LEAST TWENTY MINUTES TO THOROUGHLY COOL.
COOLING MODULES SHOULD BE CONTINUOUSLY MONITORED TO ENSURE HOT COMPONENTS DO NOT CREATE
FIRES WITH SPILLED LIQUIDS OR OTHER DEBRIS. FAILURE TO ALLOW UNIT TO COOL COULD RESULT IN BURNS,
FIRES OR PERSONAL INJURY.
H.
ALWAYS WEAR RUBBER GLOVES AND SAFETY GLASSES WHEN HANDLING A DEPLOYED AIRBAG MODULE.
CAUTION: Storage, transportation, disposal and recycling of airbag module and components must be performed in accordance with all applicable state
