LS 460 AWD V8-4.6L (1UR-FSE) (2009)
Ambient Light Sensor: Service and Repair
Removal
LIGHTING: AUTOMATIC LIGHT CONTROL SENSOR: REMOVAL
REMOVAL
1. TABLE OF BOLT, SCREW AND NUT See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
2. REMOVE COWL TOP VENTILATOR LOUVER RH See: Starting and Charging/Charging System/Alternator/Service and Repair/Removal
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
(a) Disable the AUTO TILT AWAY function by changing the customize parameter See: Steering and Suspension/Steering/Steering
Column/Testing and Inspection/Programming and Relearning.
NOTE:
Record the current customize parameter setting (whether the AUTO TILT AWAY function is enabled or disabled) in order to restore the
current setting after finishing the operation.
HINT: Performing the above operation causes the AUTO TILT AWAY function to be disabled when the engine switch is turned off.
(b) Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column.
(c) Turn the engine switch off and disconnect the cable from the negative (-) battery terminal.
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt
pretensioner activation.
NOTE:
After the engine switch is turned off, the HDD navigation system requires approximately 6 minutes to record various types of memory and
settings. As a result, after turning the engine switch off, wait 6 minutes or more before disconnecting the cable from the negative (-) battery
terminal.
4. REMOVE INSTRUMENT PANEL FINISH PANEL END RH See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal
5. REMOVE INSTRUMENT PANEL FINISH PANEL END LH See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument
Panel/Service and Repair/Removal
6. REMOVE SHIFT LEVER KNOB See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal
7. REMOVE NO. 3 BOX PANEL See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and Repair/Removal
8. REMOVE REAR CONSOLE PANEL UPPER See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
9. REMOVE CONSOLE PANEL SUB-ASSEMBLY UPPER See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service
and Repair/Removal
10. REMOVE CONSOLE REAR END PANEL See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
11. REMOVE CONSOLE COVER LOWER See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
12. REMOVE CONSOLE BOX ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
13. REMOVE SWITCH AND VOLUME CASE See: Restraint Systems/Air Bag Systems/Air Bag/Service and Repair/Steering Pad/Removal
14. REMOVE NO. 2 STEERING WHEEL COVER LOWER See: Restraint Systems/Air Bag Systems/Air Bag/Service and Repair/Steering
Pad/Removal
15. REMOVE STEERING PAD ASSEMBLY See: Restraint Systems/Air Bag Systems/Air Bag/Service and Repair/Steering Pad/Removal
16. REMOVE STEERING WHEEL ASSEMBLY See: Steering and Suspension/Steering/Steering Column/Service and Repair/Removal and
Replacement/Steering Column Assembly (W/ VGRS)/Removal
17. REMOVE STEERING COLUMN COVER (W/O Driver Monitor Camera) See: Steering and Suspension/Steering/Steering Column/Service and
Repair/Removal and Replacement/Steering Column Assembly (W/O VGRS)/Removal
18. REMOVE STEERING COLUMN COVER (W/ Driver Monitor Camera) See: Steering and Suspension/Steering/Steering Column/Service and
Repair/Removal and Replacement/Steering Column Assembly (W/ VGRS)/Removal
19. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE See: Steering and Suspension/Steering/Steering Column/Service and
Repair/Removal and Replacement/Steering Column Assembly (W/ VGRS)/Removal
20. REMOVE INSTRUMENT CLUSTER FINISH PANEL See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service
and Repair/Removal
21. REMOVE COMBINATION METER ASSEMBLY See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
22. REMOVE INSTRUMENT SIDE PANEL LH See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service and
Repair/Removal
23. REMOVE NO. 1 INSTRUMENT CLUSTER MOULDING See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument Panel/Service
and Repair/Removal
24. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER See: Body and Frame/Interior Moulding / Trim/Dashboard / Instrument