MKS AWD V6-3.7L (2009)
7. Remove the newly programmed IA key from the backup transceiver slot and press either the LOCK or the UNLOCK button on the IA key in order
to exit the key programming mode.
8. Verify the operation of the new key by pressing the LOCK and UNLOCK buttons on the IA key, then place the new key inside the passenger
compartment and start the vehicle with the new key. Make sure the original keys are outside of the vehicle when verifying the new key operation.
9. If it is desired to program an additional key (only up to 4 keys total can be programmed into the RFA module), repeat Steps 1 - 8 for the additional
key that needs to be programmed.
Key Programming Switch State Control - Integrated Keyhead Transmitter (IKT)
Key Programming Switch State Control - Integrated Keyhead Transmitter (IKT)
NOTE: The spare key programming switch is a programmable switch which provides the capability to enable/disable the normal customer spare key
programming procedure detailed in the Owner's Literature. It must read ENABLE if more than 2 keys need to be programmed into the Instrument Panel
Cluster (IPC). For additional information, refer to Key Programming Using Two Programmed Keys - Integrated Keyhead Transmitter (IKT) See:
Accessories and Optional Equipment/Antitheft and Alarm Systems/Testing and Inspection/Programming and Relearning/Key Programming Using Two
Programmed Keys - Integrated Keyhead Transmitter (IKT). This programmable switch is provided as a convenience for rental company fleets or other
fleet purchasers who may not want the spare key programming procedure available to the vehicle driver.
NOTE: The spare key programming switch state can be viewed with the Instrument Panel Cluster (IPC) PID SPAREKEY.
NOTE: If the SPAREKEY PID reads ENABLE, up to 8 keys total can be programmed into the IPC using Key Programming Using Two Programmed
Keys - Integrated Keyhead Transmitter (IKT) See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Testing and
Inspection/Programming and Relearning/Key Programming Using Two Programmed Keys - Integrated Keyhead Transmitter (IKT). If the SPAREKEY
PID reads DISABLED, the Key Programming Using Two Programmed Keys procedure does not function. This switch is set to ENABLE when the
vehicle is built. This PID does not affect the Integrated Keyhead Transmitter (IKT) Key Programming Using Diagnostic Equipment, the Spare Key
Programming - Unlimited Key Mode See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Testing and Inspection/Programming and
Relearning/Spare Key Programming - Unlimited Key Mode or the Spare Key Programming - Using Diagnostic Equipment See: Accessories and
Optional Equipment/Antitheft and Alarm Systems/Testing and Inspection/Programming and Relearning/Spare Key Programming - Using Diagnostic
Equipment procedures.
1. Insert a programmed Passive Anti-Theft System (PATS) (or IKT) key into the ignition lock cylinder and turn the key from the OFF position to the
ON position.
2. From the scan tool, enter TOOLBOX. Select BODY-SECURITY-PATS Functions and follow the on-screen instructions to ENTER SECURITY
ACCESS. For additional information, refer to Anti-Theft Security Access - Integrated Keyhead Transmitter (IKT) See: Accessories and Optional
Equipment/Antitheft and Alarm Systems/Testing and Inspection/Component Tests and General Diagnostics/Anti-Theft Security Access -
Integrated Keyhead Transmitter (IKT).
3. NOTE: The default setting of the key programming switch on delivery of all new vehicles is ENABLED, when viewing the IPC PID SPAREKEY.
From the scan tool menu select: "Customer Spare Key Programming Enable" (or "Customer Spare Key Programming Disable") and follow the
on-screen instructions.
-
"Customer Spare Key Programming Enable" - the spare key programming procedure is accessible.
-
"Customer Spare Key Programming Disable" - the spare key programming procedure is not accessible.
Key Programming Switch State Control - Intelligent Access (IA)
Key Programming Switch State Control - Intelligent Access (IA)
