Tribute 2WD L4-2.5L (2009)
Passive Anti-Theft System (PATS) Parameter Reset
PASSIVE ANTI-THEFT SYSTEM (PATS) PARAMETER RESET
NOTE:When using the integrated diagnostic system (IDS), the instrument cluster (IC) and the PCM parameters are reset at the same time.
NOTE:Once security access has been granted, multiple security access commands should be executed (if necessary) prior to exiting the command menu.
This avoids an additional security access procedure and the associated 10 minute time delay.
1. Turn the key from the OFF position to the ON position.
2. From the scan tool, enter TOOLBOX. Select BODY - SECURITY - PATS Functions and follow the on-screen instructions to ENTER
SECURITY ACCESS. See See: Accessories and Optional Equipment/Antitheft and Alarm Systems/Testing and Inspection/Programming and
Relearning/Anti-Theft Security Access.
3. From the scan tool, select: Parameter Reset and follow the IDS on-screen instructions.
NOTE:If the IC was replaced, follow Steps 4-9. If the IC and the PCM were replaced, follow Steps 4-9. If only the PCM was replaced, cycle the key off,
then back on, to complete the procedure.
4. From the scan tool, select: Ignition Key Code Erase and follow the IDS on-screen instructions.
NOTE:If steps 4-9 are followed, 2 keys must be present.
5. Turn the key to the OFF position and disconnect the scan tool.
6. Turn the key to the ON position for a minimum of 6 seconds (if it is an IKT key).
NOTE:Integrated keyhead transmitter (IKT) keys require a 6-second programming time frame for the remote keyless entry (RKE) data transfer to take
place, while standard passive anti-theft system (PATS) keys only require a minimum of 3 seconds.
7. Turn the key to the OFF position and remove it from the ignition lock cylinder.
8. Insert the second key and turn it to the ON position for a minimum of 6 seconds (if it is an IKT key).
9. Both keys will now start the vehicle and will also operate the RKE functions of the vehicle (if they are IKT keys).
10. If more keys are required to be programmed, see See: Key Programming Using Two Programmed Keys.
NOTE:The RKE data transfer will take place between the key and the IC first. After both keys are programmed into the IC, the RKE data will transfer
from the IC to the smart junction box (SJB). Until the final data transfer takes place into the SJB, the RKE functions will not operate.
Remote Keyless Entry Transmitter Programming
REMOTE KEYLESS ENTRY TRANSMITTER PROGRAMMING
NOTE:This procedure is for programming conventional keyfobs only. The remote keyless entry (RKE) transmitter of the integrated keyhead transmitter
(IKT) is programmed automatically during the passive anti-theft system (PATS) programming. See See: Key Programming Using Two Programmed
Keys or See: Integrated Keyhead Transmitter (IKT) Key Programming Using Diagnostic Equipment to program the IKT.
NOTE:All RKE transmitters must be programmed at the same time.
NOTE:Do not apply the brake pedal during this sequencing, as doing so ends the sequence and the transmitters will not be programmed.
1. Electronically unlock the door locks using the door lock control switch.
2. Cycle the ignition switch from the OFF to the RUN position 8 times in rapid succession (within 10 seconds), with the eighth turn ending in RUN.
If the module successfully enters program mode, it locks and then unlocks all the doors.
3. Within 20 seconds, press any button on the RKE transmitter to be programmed. The doors lock and then unlock to confirm that each RKE
transmitter is programmed. Repeat this step for each RKE transmitter.
NOTE:If no action is taken within 20 seconds after a transmitter has been programmed, the programming sequence ends (the doors lock and unlock to
confirm that programming is complete).
4. Exiting the programming mode is accomplished if one of the following occurs:
a. The key transitions to the OFF position
b. 20 seconds have passed since entering programming mode or since the last RKE transmitter was programmed
c. The maximum number (4) of RKE transmitters have been programmed
5. Check the operation of the RKE transmitter. If the door locks do not respond for the programmed RKE transmitter(s), wait several seconds and
