mercedesbenz Workshop Repair Guides

Mercedes Benz Workshop Service and Repair Manuals

GF91.60-P-1100CA Passenger-Side Seat Occupied Recognition Function|Page 6347 > < Seat Occupant Sensor|Locations
Page 1
background image

Seat Occupant Sensor: Description and Operation
GF91.60-P-1100CA Passenger-Side Seat Occupied Recognition Function

GF91.60-P-1100CA Passenger-side Seat Occupied Recognition Function

- except CODE (494) USA version

General function requirements

^

Circuit 15R ON

15R The electronic ignition lock control unit (N73) transmits the circuit status for circuit to the supplemental restraint system control unit (N2/10) via the
chassis CAN (CAN E)

Passenger-side seat occupied recognition, general

The front passenger seat occupation status is always sensed by the supplemental restraint system (SRS). On vehicles with code (U18) Automatic child
seat recognition (ACSR) a fitted child seat is also recognized.

The automatic child seat recognition function is only guaranteed to work with a child seat that has been approved and coded by Daimler AG. This child
seat must be equipped with two transponders (resonators), which are located at the left and right in its base.

The passenger-side seat occupied recognition consists of the following subfunctions:

^

Function sequence for front passenger seat occupied recognition

^

Function sequence for issuing status and error messages (with code (U18) Automatic child seat recognition (ACSR [AKSE]))

Function sequence for front passenger seat occupied recognition

The passenger seat occupied recognition is sensed by the front passenger seat occupied recognition (B41/1) (without code (U18) Automatic child seat
recognition (ACSR)) or front passenger seat and ACSR occupied recognition (B48) (with code (U18) Automatic child seat recognition (ACSR)).

The signals are relayed to the supplement restraint system control unit.

The following statuses are defined with code (U18) Automatic child seat recognition (ACSR):

-

Seat unoccupied:
If the seat belt is not buckled, the front passenger airbag unit, front passenger sidebag unit and front passenger emergency tensioning retractor unit
are disabled. If the seat belt is buckled, the front passenger airbag unit is switched off.

-

Seat occupied (light or heavy person):
The front passenger airbag unit is enabled (ignition of first stage or both stages).

-

Child seat detected (with code (U18) Automatic child seat recognition (ACSR [AKSE])):
The front passenger airbag unit is switched off.

Without code (U18) Automatic child seat recognition (ACSR) the occupation status of the front passenger seat does not influence the SRS deployment
characteristics. Only the assignment status for the seat belt reminder warning is determined by the instrument cluster (A1).

Function sequence for issuing status and error messages (with code (U18) Automatic child seat recognition (ACSR [AKSE]))

The output of status and fault messages consists of the following subfunctions:

^

Function sequence for actuation of the automatic child seat recognition warning lamp (S6/1e1)

^

Function sequence for outputting fault messages

Function sequence for actuation of the automatic child seat recognition warning lamp

The signal for switching on the automatic child seat recognition warning lamp when a child seat is detected is sent by the supplemental restraint system
control unit over the chassis CAN to the front SAM control unit with fuse and relay module (N10/1). This switches the automatic child seat recognition
warning lamp on or off over the instrument panel LIN (LIN 1).

Function sequence for outputting fault messages

If the seat occupied and automatic child seat recognition sensor is defective or communication with the supplemental restraint system control unit is
interrupted (e.g. plug not connected), the automatic child seat recognition warning lamp is also switched on. A fault is also stored in the restraint systems
control unit and an appropriate message is shown on the instrument cluster.

The supplemental restraint system control unit sends the corresponding information over the chassis CAN to the instrument cluster.
If the child seat is defective or improperly positioned (only one resonator detected), the supplemental restraint system warning lamp (A1e15) in the

GF91.60-P-1100CA Passenger-Side Seat Occupied Recognition Function|Page 6347 > < Seat Occupant Sensor|Locations