Mariner 4WD L4-2.5L (2010)
3. Press and hold the RESET button (for approximately 2 seconds) until MARK THIS KEY AS RESTRICTED is displayed.
4. Wait until KEY RESTRICTED AT NEXT START is displayed, then release the RESET button.
3. The MyKey(TM) feature (standard restricted features) is successfully programmed into this particular key. Make sure it is labeled for easy
identification. To customize the MyKey(TM) with the audio volume limited, maximum speed limit, speed alert chimes, and AdvanceTrac(R)
on/off restrictions, refer to Configuring MyKey(TM) Optional Restricted Features.
-
If the vehicle is equipped with remote start, also refer to Using MyKey(TM) with Remote Start Systems.
Configuring MyKey(TM) Optional Restricted Features
NOTE: The following features can be restricted on a MyKey(TM):
-
audio volume level set to a pre-determined level (45% of the maximum volume)
-
maximum speed limit of 130 km/h (80 mph) on or off
-
speed alert chimes set for 75, or 90 or 105 km/h (45, or 55 or 65 mph)
-
AdvanceTrac(R) always on feature turned on or off
1. NOTE: If programming or configuring a MyKey(TM), but then decide to clear the key instead, do not turn the key to the OFF position. Follow
the Disable MyKey(TM) Restricted Features procedure to clear the key of any restricted MyKey(TM) status. If necessary, refer to Information and
Message Center in the Description and Operation portion of Instrument Panel, Gauges and Warning Indicators for MyKey(TM) system checks and
system warnings displays.
To configure the MyKey(TM) optional restricted features listed directly above, carry out the following:
1. Using an admin key that has not been programmed as a MyKey(TM), turn the key to the ON position.
2. Press and hold the SETUP button until RESET FOR MYKEY SETUP is displayed.
3. Press and release the RESET button to display the MyKey(TM) setup menus. The first programmable feature is: MYKEY MAX MPH [80
MPH] OFF.
-
To change the status of a feature that appears, press SETUP to accept the current setting and the message center displays the next feature.
-
To change the status of the feature that is displayed, press RESET to turn a feature on/off (or toggle between choices). After the feature
selection has been made, press and release SETUP to accept and the message center displays the next feature.
4. Repeat the process for the next features:
-
MYKEY MPH TONES 45 55 65 [OFF] (choose the desired speed for the chime to sound)
-
MYKEY VOLUME LIMIT [ON] OFF (choose the audio volume to be limited to 45%)
-
MYKEY ADVTRAC CTRL ON [OFF] (choose for the AdvanceTrac(R) to be automatically locked on or able to be turned on or off by
the MyKey(TM) driver)
Disable MyKey(TM) Restricted Features
1. NOTE: This procedure is used to disable the MyKey(TM) feature on all of the keys that are programmed to the vehicle. All of the keys then
operate as normal (admin) keys with no restrictions.
Insert an admin key into the ignition lock cylinder and turn the key to the ON position.
2. Press SETUP until PRESS RESET TO CLEAR MYKEY appears.
3. Press and hold RESET until HOLD RESET TO CONFIRM CLEAR and ALL KEYS ARE CLEARED is displayed.
-
A MyKey(TM) can also be cleared during the same key cycle that it was programmed by following Steps 2 and 3 of this procedure.
Check MyKey(TM) System Status
1. The vehicle system check provides the status of the following MyKey(TM) parameters:
-
MYKEY DISTANCE - This odometer only tracks mileage when a MyKey(TM) is used. If mileage does not accumulate, the intended
MyKey(TM) is not being used or the IC is at fault. The only way to reset this odometer to zero is by disabling the MyKey(TM). If this
odometer is lower than the last time it was checked, the MyKey(TM) system has been cleared. If desired, it may be necessary to program the
MyKey(TM) restricted features into the key.
-
# MYKEY(S) PROGRAMMED - Indicates how many MyKeys(TM) are programmed to the vehicle. It can also be used to determine if a
MyKey(TM) has been disabled.
