Lancer L4-2.4L SOHC (2005)
-
If the windshield mist wiper switch is turned to the ON position with the ignition switch at the "ACC" or "ON" position, the mist wiper high-speed
operation signal is sent to the front-ECU. This signal turns on the wiper speed switching relay, causing the wipers to work at high-speed while the
mist switch is on.
-
While the windshield mist wiper switch remains turned on when the intermittent mode is still working, the wipers work as the mist wiper.
However, the wipers return to the intermittent mode again when the switch is changed back to "INT" position.
-
To prevent the windshield mist wiper from operating when the windshield wiper switch is turned OFF, the windshield mist wiper does not work
for 0.5 second after the windshield intermittent wiper switch, the windshield low-speed wiper switch and the windshield high-speed wiper switch
are turned OFF.
WINDSHIELD WASHER OPERATION
-
If the windshield washer switch is turned to ON position with the ignition switch at "ACC" or "ON" position, the windshield washer ON signal is
sent to the front-ECU, causing the windshield wiper signal to turn on after 0.3 second. After the wind-shield washer switch signal turns off, the
wind-shield wiper signal turns off in three seconds.
-
If the windshield washer switch is turned on while the windshield wiper is at intermittent mode, when the windshield washer switch is turned OFF
within 0.2 second, the wiper works only once to perform mist operation by the windshield washer switch. When the ON condition of the
windshield washer switch continues more than 0.2 second, the wiper performs the same movement as normal condition from the time when 0.2
second has elapsed and then returns to the intermittent motion.
SEAT BELT WARNING LIGHT
<VEHICLES WITHOUT KEYLESS ENTRY SYSTEM>
If the driver turns the ignition switch to the "ON" position without wearing the seat belt, the seat belt warning light illuminates to alert the driver to wear
the seat belt.
<VEHICLES WITH KEYLESS ENTRY SYSTEM>
If any of the following conditions is met with the ignition switch at "ON" or "ST", the ETACS-ECU illuminates or extinguishes the seat belt indicator by
using the driver's seat belt switch signal and the vehicle speed signal.
-
The seat belt switch is turned on (driver's seat belt is not fastened) with the ignition switch at "ON" or "ST".
-
Flashes the indicator 11 cycles (after 0.5 seconds) if any of the following conditions is met when sixty seconds or more have elapsed since the
ignition switch is turned "ON", and then illuminates it for eight seconds. One cycle consists of five-second "on" and then three-second "off".
NOTE: Once this timer operation has been activated, it will not be activated again until the vehicle speed reduces to 3 km/h (2 mph) or less even
if any of the following conditions is met.
a. The vehicle speed has reached 8 km/h (5 mph) while the seat belt switch is turned on (driver's seat belt is not fastened) with the ignition switch
"ON.
b. The seat belt switch has been turned on (driver's seat belt has not been fastened) for at least ten seconds while the ignition switch has been
turned "ON" and the vehicle speed has been 8 km/h (5 mph) or more.
The indicator stops illuminating if the ignition switch or the seat belt switch is turned off (the driver's seat belt is fastened) while the timer operation is
active.
HEADLIGHT
HEADLIGHT AUTOMATIC SHUTDOWN
FUNCTION
When the headlights or taillights are on, and the ignition switch is turned from "ON" to "LOCK" (OFF) or "ACC" position or the ignition key is
removed, the headlights will be switched off in three minutes. If the driver's door is opened within that three-minute period, the headlights will be
switched off automatically. This prevents the battery from discharging.
NOTE: The headlight automatic shutdown function can be disabled by the SWS configuration function.
HEADLIGHT DIMMER SWITCH AUTOMATIC RESETTING FUNCTION
This function allows the dimmer switch to be reset to the low-beam position whenever the headlight switch is turned to the ON position.
FLASHER TIMER
TURN-SIGNAL LIGHT
When the ignition switch is turned to the "ON" position and turn-signal light switch is placed in the ON position for right or left turn-signaling, the
system generates turn-signal light drive signals (flashing signals). The system also notifies of a blown turn-signal light bulb by shortening the flashing
intervals of the corresponding indicator light.
