Raider 4WD V6-3.7L SOHC (2007)
SHIFT REQUIREMENTS
If the FCM is in full power mode and at functionality level zero, it uses the following criteria to determine if a shift is allowed.
If any of the driver controllable conditions are not met once the shift request is recognized, the FCM may illuminate one or more of the 4WD system
message icons in the instrument cluster display.
Mode shifts will be allowed regardless of transmission gear or vehicle speed, whenever the following conditions are met
-
Ignition key switch is in the RUN position.
-
Front and rear wheel speed are within 21 km/hr (13 mph).
-
A change in the Selector switch state indicates that a mode shift has been requested.
-
A valid mode sensor signal is being sensed by the FCM.
-
Proper transmit/receive messages are occurring on the CAN bus.
-
An Anti-lock Brake System (ABS) event is not in progress.
Range shifts will be allowed only if all of the following conditions are met:
-
Ignition key switch is in the RUN position.
-
Front and rear wheel speed are within 21 km/hr (13 mph).
-
A change in the Selector Switch state indicating a range shift has been requested.
-
Transmission in NEUTRAL signal must be recognized for at least 1.5 seconds ±100 msec. (Automatic transmissions only)
-
Proper transmit/receive messages are occurring on the CAN bus.
-
Clutch signal is recognized for 500 msec ± 50 msec (Manual transmissions only).
-
Vehicle speed is less than or equal to 4.8 km/hr (3 miles per hour).
-
A valid mode sensor signal is being sensed by the FCM.
-
An Anti-lock Brake System (ABS) event is not in progress.
A shift into transfer case Neutral will be allowed only if all of the following conditions are met:
-
Ignition key switch is in the RUN position, engine off.
-
Front and rear wheel speed are within 21 km/hr (13 mph).
-
The recessed Neutral Selection switch has been depressed continuously for 4.0 seconds ±100 msec while all shift conditions have been
continuously met.
-
Transmission in NEUTRAL signal recognized from the bus. (Automatic transmissions only)
-
Clutch signal is recognized from the bus (Manual transmissions only).
-
Proper message transmissions/receptions are occurring on the CAN bus.
-
Vehicle speed is less than or equal to 4.8 km/hr (3 miles per hour).
-
Foot Brake is applied.
-
A valid mode sensor signal is being sensed by the FCM.
-
An Anti-lock Brake System (ABS) event is not in progress.
A shift out of transfer case Neutral will be allowed only if all of the following conditions are met:
-
Ignition key switch is in the RUN position.
-
Front and rear wheel speed are within 21 km/hr (13 mph).
-
The recessed Neutral Selection switch has been depressed continuously for 1.0 seconds ±100 msec while all shift conditions have been
continuously met.
-
Transmission in NEUTRAL signal recognized from the bus. (Automatic transmissions only)
-
Clutch signal is recognized from the bus (Manual transmissions only).
-
Proper message transmissions/receptions are occurring on the CAN bus.
-
Vehicle speed is less than or equal to 4.8 km/hr (3 miles per hour).
-
A valid mode sensor signal is being sensed by the FCM.
-
An Anti-lock Brake System (ABS) event is not in progress.
LAMP STRATEGY
The following strategy for the FCM controlled transfer case system uses the instrument cluster VF display's 4LOCK, 4LO, Service 4WD, and Mode
Switch Transfer Case Neutral LED. Flashing any of the amps or LED is accomplished at a 2Hz rate.
NOTE: There is no lamp for the 2WD or AWD position. If no 4WD system message icons are illuminated in the instrument cluster, the operator is to
assume that the transfer case is in the 2WD or AWD position.
-
2WD or AWD to 4LO - Successful shifts will flash 4LO during a shift, then after the 4LO position has been met, display the 4LO lamp solid. In
the blocked condition, flash the 4LO lamp during the 5 Phase 1 shift attempts. After 5 unsuccessful attempts, the transfer case remains in 2WD or
AWD and no lamps are illuminated. When shift conditions are not met, no shift attempts are made and the 4LO lamp is flashing.
-
2WD or AWD to 4LOCK - Successful shifts will flash 4LOCK during a shift, then after the 4LOCK position has been met, display the 4LOCK
lamp solid. In the blocked condition, flash the 4LOCK lamp during the 5 Phase 1 shift attempts. After 5 unsuccessful attempts, the transfer case
