911 Carrera 4 Cabriolet (996) F6-3.4L (1999)
-
Select "Right or left-hand drive" in the menu corresponding to the vehicle equipment and code with the [F8]
key.
-
Air conditioning
Under this menu item, the PCM2 GW
with/without.
corresponding to the air conditioning equipment can be coded.
-
Connect and start the 9588 Porsche System Tester II and switch on the ignition.
-
Select '911 (996)' in the Vehicle type menu and confirm with the [>>] key.
-
Select 'PCM' in the Control modules menu and confirm with the [>>] key.
-
Select 'PCM2 GW' in the PCM2 function selection and confirm with the [>>] key.
-
Select 'Coding' in the PCM2 GW function selection and confirm with the [>>] key.
-
Select 'Air conditioning with/without' in the PCM2 GW coding function selection and confirm with the [>>]
key.
-
Select "Air conditioning with/without" corresponding to the equipment in the Modify PCM2 GW coding
function selection and code with the [F8] key.
-
Country coding.
Using this menu item, you can code the country code.
-
Connect and start the 9588 Porsche System Tester II and switch on the ignition.
-
Select '911 (996)' in the Vehicle type menu and confirm with the [>>] key.
-
Select 'PCM' in the Control modules menu and confirm with the [>>] key.
-
Select 'PCM2 GW' in the PCM2 function selection and confirm with the [>>] key.
-
Select 'Coding' in the PCM2 GW function selection and confirm with the [>>] key.
-
Select "Country coding" in the PCM2 GW Coding function selection and confirm with the [>>] key.
-
Select 'the relevant country coding' from the menu item that is displayed and code it with the [F8] key.
-
MOST switch.
Under this menu item, the MOST switch corresponding to the vehicle configuration can be coded.
-
Connect and start the 9588 Porsche System Tester II and switch on the ignition.
-
Select '911 (996)' in the Vehicle type menu and confirm with the [>>] key.
-
Select 'PCM' in the Control modules menu and confirm with the [>>] key.
-
Select 'PCM2 GW' in the PCM2 function selection and confirm with the [>>] key.
-
Select 'Coding' in the PCM2 GW function selection and confirm with the [>>] key.
-
Select 'MOST switch open/closed' in the PCM2 GW coding function selection and confirm with the [>>] key.
-
Select 'MOST switch open/MOST switch closed' from the menu displayed and code with the [F8] key.
The following selection is available:
-
MOST switch open
-
MOST switch closed
-
PCM2 code.
It is possible to code the PCM2 code under this menu item after replacing the PCM2.
-
Connect and start the 9588 Porsche System Tester II and switch on the ignition.
-
Select '911 (996)' in the Vehicle type menu and confirm with the [>>] key.
-
Select 'PCM' in the Control modules menu and confirm with the [>>] key.
-
Select 'PCM2 GW' in the PCM2 function selection and confirm with the [>>] key.
-
Select 'Coding' in the PCM2 GW function selection and confirm with the [>>] key.
-
Select 'PCM2 code' in the PCM2 GW coding function selection.
-
Take the PCM2 code from IPAS, enter it and code it with the [F8] key.
-
Production mode.
The PCM2 is set to the 'Production mode ON' low-power mode in the factory and this must be switched off when
put into service.
-
Connect and start the 9588 Porsche System Tester II and switch on the ignition.
-
Select '911 (996)' in the Vehicle type menu and confirm with the [>>] key.
-
Select 'PCM' in the Control modules menu and confirm with the [>>] key.
-
Select 'PCM2 GW' in the PCM2 function selection and confirm with the [>>] key.
-
Select 'Coding' in the PCM2 GW function selection and confirm with the [>>] key.
-
Select 'Production mode' in the PCM2 GW Coding function selection and confirm with the [>>] key.
-
Select 'Production mode OFF' from the menu item displayed and code it with the [F8] key.
The following selection is available:
-
Production mode on
-
Production mode off
-
Tuner parameters.
Using this menu item, you can code the tuner parameters (country-specific tuner setting) for the country of
registration.
-
Connect and start the 9588 Porsche System Tester II and switch on the ignition.
-
Select '911 (996)' in the Vehicle type menu and confirm with the [>>] key.
-
Select 'PCM' in the Control modules menu and confirm with the [>>] key.
-
Select 'PCM2 GW' in the 911 (996) PCM2 function selection and confirm with the [>>] key.