900 S Sedan V6-2498cc 2.5L DOHC (1995)
In regard to the lighting systems, the ICE controls the relays for the lights, main and dipped beam, and extra fog lights.
Main and dipped beam are monitored by means of a filament monitor located together with the lighting relays in the main fuse box in the
engine bay.
The ICE monitors the rear parking lights, brake lights and high-level brake light.
Should a rear light bulb fail, the ICE informs the SID unit which grounds the "Defective lamp" warning lamp in main instrument display panel
1 or displays a message and lights up the "INFO DISPL" lamp in main instrument display panel 2.
The ICE also controls a "Follow-me-home" function, i.e. if the dipswitch is actuated after the door is opened, dipped beams will continue to
shine for about 30 seconds after the door is closed.
2. Wash/Wipe Systems
The ICE controls the relays for intermittent wiper operation and wiping after washing of the windshield and rear window.
The ICE controls the windshield and rear window wipers so that they will be synchronized after a single sweep cycle.
When the windshield and rear window have been washed and the wipers have completed 3-4 cycles, the ICE causes the windshield wipers to
carry out an extra sweep cycle after 8 seconds and the rear window wiper an extra sweep cycle after 16 seconds.
The relays are located in the main fuse box under the dashboard adjacent to the steering column.
3. Instrumentation Systems
The ICE sends information to the SID unit and the main instrument display panel:
^ on the sound the SID unit is to generate, e.g. "tick tack" for the direction indicators or "ding dong" for the seat-belt and ignition key
warning.
^ on a defective rear lamp bulb or brake light so that the "DEFECTIVE LAMP" indicator lamp lights up in main instrument display panel
1 or the "INFO DISPL" lamp in main instrument display panel 2 with clear text in the SID unit's display.
^ on coolant temperature to the main instrument display panel.
4. Climate Systems
The ICE controls the relay for heating of the rear window and door mirrors and monitors one or two pressure switches in the A/C system.
Information that the A/C compressor is going to be turned ON passes via the ICE control module. This is so that the ICE control module can
turn OFF the compressor if the coolant temperature is exceptionally high.
For control of the radiator fan in the event of high pressure in the A/C system, see also Cooling System.
5. Cabin Systems
The ICE controls the interior lighting and reading lamps by grounding them. It also lights up the seat-belt warning lamp on the dashboard for 6
seconds when the ignition is switched ON.
Some cars have a seat-belt reminder with a "ding-dong" sound and an ignition key reminder. The ICE sends information to the SID unit which
generates the sound. See also Instrument Panel, Gauges and Warning Indicator systems.
The electrically adjustable seats can be operated if a door is open or if the ignition is switched on (+54 circuit).
If a door is left open for more than 20 minutes, the ICE switches OFF the interior lighting and stops grounding the seat relay to save the
battery.
6. Charging System
The ICE checks battery voltage continuously and after a time may switch OFF the electrically heated rear window and electrically heated door
mirrors if battery voltage is abnormally high or low.
7. Cooling System
The ICE control module receives continuous information on the temperature of the cooling system from the coolant temperature sensor.
One or two pressure sensors in the A/C system close under different pressure conditions, causing pins 22 and 69 of the ICE control module to
be grounded. If the temperature or pressure is too high, the ICE turns ON the radiator fan by grounding the relay or relays.
If there are two relays, the radiator fan can be run at both high and low speed.
8. Engine Systems
The ICE sends a signal to the M2.10.3 engine management system when the radiator fan is going to be turned ON or OFF.
