Aura V6-3.5L (2007)
HVAC Control Module Malfunction
1. Ignition OFF, disconnect the harness connector C1 at the HVAC control module.
2. Ignition OFF, test for less than 1 ohm of resistance between the ground circuit terminal B5 and ground.
‹› If greater than the specified range, test the ground circuit for an open/high resistance.
3. Ignition ON, verify the scan tool Manual HVAC Rear Defog Sw parameter is OFF.
‹› If not the specified value, test the signal circuit terminal A8 for a short to ground. If the circuit tests normal, replace the BCM.
4. Install a 3-amp fused jumper wire between the signal circuit terminal A8 and ground. Verify the scan tool Manual HVAC Rear Defog Sw
parameter is ON.
‹› If not the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the BCM.
5. If all circuits test normal, test or replace the HVAC control module.
Rear Defog Indicator Malfunction
1. Ignition OFF, disconnect the harness connector C1 at the HVAC control module.
2. Disconnect the R/WDO DEFOG relay.
3. Connect a test lamp between the control circuit terminal B8 and ground.
4. Ignition ON, command the Rear Defog Relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the
commanded states.
‹› If the test lamp is always ON, test the control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
‹› If the test lamp is always OFF, test the control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the
BCM.
5. If all circuits test normal, test or replace the HVAC control module.
Rear Defogger Malfunction
1. Ignition OFF, disconnect the R/WDO DEFOG relay.
2. Ignition OFF, test for less than 1 ohm of resistance between the relay coil ground circuit and ground.
‹› If greater than the specified range, test the relay coil ground circuit for an open/high resistance.
3. Ignition ON, verify that a test lamp does not illuminate between the relay controlled output circuit and ground.
‹› If the test lamp illuminates, test the relay controlled output circuit for a short to voltage.
4. Verify that a test lamp illuminates between the relay switch side B+ circuit and ground.
‹› If the test lamp does not illuminate, test the relay switch B+ circuit for a short to ground or an open/high resistance. If the circuit tests normal
and the fuse is open, test the relay controlled output circuit for a short to ground.
5. Ignition OFF, disconnect the harness connector at the rear window defogger grid.
6. Ignition OFF, test for less than 1 ohm of resistance between the rear window defogger grid ground circuit terminal A and ground
‹› If greater than the specified range, test the ground circuit for an open/high resistance.
7. Connect the harness connector C1 at the rear window defogger grid.
8. Ignition ON, connect a 30-amp fused jumper wire between the relay switch B+ circuit and the relay controlled output circuit. Verify the rear
window defogger grid is activated.
‹› If the rear window defogger grid does not activate, test the relay controlled output circuit for an open/high resistance. If the circuit tests
normal, test or replace the rear window defogger grid.
9. Connect a test lamp between the rear defogger control circuit and the relay coil ground circuit.
10. Command the rear defog relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded
states.
‹› If the test lamp is always ON, test the rear defogger control circuit for a short to voltage. If the circuit tests normal, replace the BCM.
‹› If the test lamp is always OFF, test the rear defogger control circuit for a short to ground or an open/high resistance. If the circuit tests normal,
replace the BCM.
