Leon Mk2
Note
|
1 - | clutch housing |
2 - | Oil relay washer |
3 - | Dished washer |
q | Remove → Fig. |
q | Insertion → Fig. |
4 - | Outer ring of roller bearing |
q | Remove → Fig. |
q | Insertion → Fig. |
5 - | Inner ring of roller bearing |
q | Releasing → Fig. |
q | Insertion → Fig. |
6 - | Secondary shaft for 1ª to 4ª gear |
q | Adjustment → Chapter |
7 - | Needle bearing for the 3rd gear |
8 - | 2nd speed selector gear |
9 - | Synchronizer ring (interior ring of the 2ndª gear |
q | Check for wear → Fig. |
q | Check that the tabs show no signs of wear |
q | Installation position → Fig. |
10 - | Outer ring for 2nd gear |
q | Replace this if there are grooves or treads caused by wear |
q | Fit to the synchro ring → Item |
q | Installation position → Fig. |
11 - | Synchromesh ring of 2nd gear |
q | Check for wear → Fig. |
q | Installation position → Fig. |
12 - | Mobile sleeve/synchroniser body of the 1stª and 2ndª gear |
q | Release along with the 6th gear mobile pinion → Item after removing the securing ring → Fig. |
q | Dismantling → Fig. |
q | Assembling the mobile element/synchroniser body → Fig. |
q | Installation position → Fig. |
q | Insertion |
13 - | Circlip |
14 - | Synchromesh ring of 1st gear |
q | Check for wear → Fig. |
q | Fit so that the recesses insert in the locking parts of the mobile element. → Item |
15 - | Outer ring for 1st gear |
q | Replace this if there are grooves or treads caused by wear |
q | Fit to the synchro ring → Item |
q | Installation position → Fig. |
16 - | Synchronizer ring (interior ring of the 1stª gear) |
q | Check for wear → Fig. |
q | Check that the tabs show no signs of wear |
q | Installation position → Fig. |
17 - | Needle bearing for the 1st gear |
18 - | 1st speed selector gear |
q | Installation position → Fig. |
19 - | Thrust ring for the 1stª and 4thª gear |
q | 2 pieces |
q | Insert the thrust ring tab into the hole of the secondary shaft |
20 - | Glass |
q | Keep the thrust rings → Itemin place on the secondary shaft |
21 - | Needle bearing for the 4th gear |
22 - | 4th gear wheel |
23 - | Syncromesh ring for 4th gear |
q | Check for wear → Fig. |
24 - | Mobile sleeve/synchroniser body of the 3rdª and 4thª gear |
q | After upgrading the locking ring → Fig. remove the gear 4ª with the rack wheel → Item |
q | Dismantling → Fig. |
q | Installation position of the mobile element/synchroniser body. → Fig. |
q | Assembling the mobile element/synchroniser body. → Fig. and → Fig. |
q | inster → Fig. |
25 - | Circlip |
26 - | Synchromesh ring of 3rdª gear |
q | Check for wear → Fig. |
27 - | Outer ring for 3rd gear |
q | Replace this if there are grooves or treads caused by wear |
q | Fit to the synchro ring → Item |
q | Installation position → Fig. |
28 - | Synchronizer ring (interior ring of the 3rd gear) |
q | Check for wear → Fig. |
q | Check that the tabs show no signs of wear |
q | Installation position → Fig. |
29 - | Needle bearing for the 3rdª gear |
30 - | 3rd speed selector gear |
q | Installation position → Fig. |
31 - | Inner ring of roller bearing |
q | Remove → Fig. |
q | Insertion → Fig. |
32 - | Circlip |
q | When tapered roller bearing → Item or input shaft → Item are renewed: determine thickness of required circlip → Fig. |
33 - | Outer ring of roller bearing |
q | Remove → Fig. |
q | Insertion → Fig. |
34 - | Shim |
q | Determine thickness → Chapter |
35 - | Gearbox |