Leon Mk2
Electrical and electronic components and their locations |
1 - | Automatic gearbox control unit -J217- |
q | Fitting location → Fig.. |
q | Removing → Fig.. |
q | Installing → Fig.. |
q | The control unit transmits and receives data from the data bus. |
2 - | Engine control unit |
q | Location and removing and installing → Fig.. |
q | The control unit transmits and receives data from the data bus. |
3 - | Selector lever position display -Y6- |
q | Fitting location → Fig.. |
q | Simultaneous illumination of all selector lever position display segments indicates gearbox emergency running mode. |
4 - | Diagnostic connection |
q | Fitting location → Fig.. |
5 - | Multi-function switch -F125- |
q | Removing, installing and adjusting → Chapter. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
6 - | Intermediate shaft speed sender -G265- |
q | Picks up a signal at gear A (intermediate speed). |
q | Location: in gearbox. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
q | Removing and installing → Chapter. |
7 - | Vehicle speed sender -G68- |
q | Measures gearbox output shaft speed (vehicle speed). |
q | Location: in gearbox. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
q | Removing and installing → Chapter. |
8 - | Gearbox input speed sender -G182- |
q | Measures gearbox input shaft speed (turbine shaft). |
q | Location: in gearbox. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
q | Removing and installing → Chapter. |
9 - | Gearbox oil temperature sender -G93- |
q | Location: in gearbox. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
q | As part, available only with gearbox wiring harness → Electronic parts catalogue “ETKA”. |
q | Removing and installing → Chapter. |
10 - | Selector lever lock solenoid -N110- |
q | Location and removing and installing → Chapter. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
11 - | Brake pressure switch -F270- |
q | Location: switch is located on front wall, in brake line to front right brake calliper. |
q | Signal can be checked using “guided fault finding” of -VAS 5051-. |
12 - | Valve body |
q | Location: in gearbox. |
q | Removing and installing → Chapter. |
q | The solenoid valves -N88-, -N89-, -N90-, -N91-, -N92-, -N93-, -N281-, -N282- and -N283- are attached to the valve body → Chapter. |
q | The valves can be checked using “guided fault finding” of -VAS 5051-. |
13 - | Brake light switch -F- |
q | Location and removing and installing → Fig.. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
14 - | Starter inhibitor and reversing light relay -J226- |
q | Fitting location → Fig.. |
15 - | Kickdown switch -F8- |
q | Fitting location → Fig.. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
16 - | Tiptronic switch -F189- |
q | Removing and installing → Chapter. |
q | Can be checked using “guided fault finding” of -VAS 5051-. |
17 - | Throttle valve potentiometer -G69- or accelerator pedal position sender -G79- |
q | → Fig. |
18 - | Cruise control system switch -E45- |
q | Fitting location → Fig.. |
q | Removing and installing → Electrical system; Rep. Gr.94. |
|
|
|
|
|
|
|
|
|
|
|
|