SEAT Workshop Service and Repair Manuals

Removing and installing mechatronic unit for dual clutch gearbox -J743- (gearbox installed) Removing and installing with gearbox removed is described in → Chapter. Special tools and workshop equipment required

t  Torque wrench -V.A.G 1331-

t  Used oil collection and extraction unit -V.A.G 1782-

t  Adapter for oil filling -VAS 6262 A-

t  Assembly tool -T10465- Removing mechatronic unit Always make sure that no dirt can enter an »open« gearbox. In particular, dirt entering an exposed mechatronic unit for dual clutch gearbox -J743- and / or oil pump can lead to gearbox failure. Please also refer to the notes on the oil filter change regarding »dirty oil« → Chapter. The mechatronic unit can stick on the dowel pins when the gearbox is very warm. Then let the gearbox cool off. –  Raise vehicle. All 4 supports of lifting platform must be at same height. –  Shift selector lever into position „P“. –  Remove noise insulation → General body repairs, exterior; Rep. gr.50. If present:

–  Remove connecting hose between charge air cooler and charge air pipe → Rep. gr.21.   Note It is possible that parts having nothing to do with the mechatronic unit must be removed. This depends on the vehicle's equipment. This will create enough space to remove the mechatronic unit.

t  Depending on the vehicle, these parts may include, for example, t  Radiator fan support t  Additional lines for air conditioner t  Charge air or air cooling pipes t  For example, the left wheel housing liner must be removed from the Scirocco with the 2-litre petrol engine.

–  Release mechatronic unit connector -1- by turning and pull off connector.   Note Disregarding of -item A-.

–  Unbolt wiring retainer from front of »large« gearbox cover (2 nuts M6). Tightening torque: 10 Nm –  Raise lines near cover and tie. –  Position used oil collection and extraction unit -V.A.G 1782- under gearbox in area of »large« cover.   Caution Oil runs out of cover when bolts are unscrewed. Hot gearbox oil can cause burns.

–  Loosen bolts -arrows- of cover diagonally and remove. Hold cover when doing this. –  Allow oil to drain out and then remove cover with seal. About 3 litres of oil will drain.   Note »Small« cover of oil pump, as well as seal and bolts of »large« cover must always be renewed.

–  Remove oil pump cover -A-.

–  Screw out the bolts -2, 3- that fix the pendulum support to gearbox → Rep. gr.40. This allows the gearbox to be »pushed back« a little in order to remove the mechatronic unit.

Before touching mechatronic unit, touch an earthed object → Chapter.

–  Release connector -1- of gearbox input speed sender -G182- and oil temperature sender in multi-plate clutch -G509- using release tool -T10465- and pull connector off.

–  First pull line out of lower clip -arrow I-. –  Then remove it from upper clip -arrow II- and lay to side. Do not kink line.

–  Loosen securing bolts -1- through -10- in given order and remove.

–  Carefully pull mechatronic unit out of gearbox housing so that sender arm -B- on back is no longer in gearbox housing. When handling mechatronic unit, pay special attention to the »long« sender arm. –  Carefully swing mechatronic unit for dual clutch gearbox -J743- downwards.

Laying mechatronic unit to side properly   Caution DO NOT lift the mechatronic unit by the sender »arm« or put down the unit so it rests on the sender arm.

If »arm« is damaged, mechatronic unit must be renewed. Installing mechatronic unit Before touching mechatronic unit, touch an earthed object → Chapter.

–  Carefully set mechatronic unit for dual clutch gearbox -J743- in gearbox housing. –  Do not pinch wiring. –  Carefully set mechatronic unit on dowel pins -arrow-. Ensure that »sender arm« locates in its -fitting position-. –  Look to see if mechatronic unit has made contact correctly.

–  Screw in new bolts -1- through -10- hand-tight. –  Tighten bolts in given order to 5 Nm + 90° (1/4 turn). –  Hook line -A- first in upper retaining lug, and then in lower -arrows-. –  Push on connector and engage.

–  Renew both -O-rings- if you reinstall the »old« mechatronic unit. Of course a »new« mechatronic unit already has »new« seals. –  Moisten O-rings with dual clutch gearbox oil. –  Clean cover seal and sealing surfaces on gearbox. –  Ensure proper seating of seal. –  Set cover over mechatronic unit, being careful not to pinch any wiring.

–  Insert new bolts -arrows- and tighten diagonally in several stages to 10 Nm.

–  Set new oil pump cover -A- in place and tighten bolts -arrows- diagonally in several stages to 8 Nm. –  Attach wire retainer to cover and tighten nuts to 10 Nm. –  Push on connector for mechatronic unit for dual clutch gearbox -J743- and engage lock by turning. –  If fitted, fit the hose joining the intercooler and the booster air pipe → Rep. gr.21. –  Reinstall any parts which may have been removed from the vehicle.

–  Do not start the engine. –  Please renew filter if oil is contaminated → Chapter. –  Connect → Vehicle diagnostic tester. –  Position used oil collection and extraction unit -V.A.G 1782- under gearbox in area of oil drain plug.

–  Remove oil drain plug close to pendulum support -arrow-.

–  Before screwing adapter for oil filling -VAS 6262 A- onto oil bottle, measure length of breather pipe, dimension -a- and shorten → Anchor. Dimension -a- = 210 mm   Note The dimension -a- is measured from the shaft (green area in the counting glass) of the adapter for oil filling -VAS 6262 A-.

–  Screw the adapter for filling -VAS 6262 A- hand tight into the inspection hole.

–  Shake bottles before opening. –  Fill 3 litres of oil. –  To change the bottle, the valve must be closed or the adapter for the oil filling -VAS 6262 A- must be held above the gearbox. Next, start engine, check oil level and top up oil. The adapter for the oil filling -VAS 6262 A- must remain installed. –  Check the oil level and top-up if necessary → Chapter. –  Install noise insulation → General body repairs, exterior; Rep. gr.50. –  Perform basic setting.