SEAT Workshop Service and Repair Manuals

The metering unit is an electromagnetic swivelling positioner which is controlled by the control unit via a directed duty cycle (on-off ratio). The eccentric shaft on the metering unit moves the modulating piston on the high pressure piston and thereby regulates the quantity of fuel injected.

The modulating piston movement sender informs the control unit of the position of quantity adjuster -N146 and therefore stipulates the amount injected.

Special tools, testers, measuring instruments and auxiliary items required

• ◆ Fault reader V.A.G 1551 or vehicle system tester V.A.G 1552 with cable V.A.G 1551/3
• ◆ Test box V.A.G 1598/18
• ◆ Hand multimeter V.A.G 1526 or multimeter V.A.G 1715
• ◆ Adapter set V.A.G 1594
• ◆ Current flow diagram

Test sequence

• ‒ Connect fault reader V.A.G 1551 (V.A.G 1552) and select engine electronics control unit with the "Address word" 01. When doing this the engine must be running at idling speed.
  (Connecting fault reader and selecting engine electronics control unit .)

• ‒ Press keys 0 and 8 for the function "Read measured value block" and confirm entry with Q key.

• ‒ Press keys 0, 0 and 1 for "Display group number 1" and confirm entry with Q key.

• ‒ Check coolant temperature in display zone 4.
      Specification: at least 85 °C

Continue with check only when coolant temperature is attained.

• ‒ Check display in display zone 3 (voltage supplied from modulating piston movement sender).

• ‒ If specification is not obtained, check modulating piston movement sender and quantity adjuster as described in following:

Checking modulating piston movement sender (G149).

• ‒ Press the ⇒key.
• ‒ Press keys 0 and 6 for the "End data transfer" function and confirm input with the Q key.

• ‒ Switch off ignition.
• ‒ Disconnect connector for (connection to injection pump quantity adjuster) sender =>Fitting locations overview Page 23-4

Engine codes AFN, AVG:

• ‒ → Measure resistance between connector contacts 1 + 2 and 2 + 3.
      Specification: 5 ... 7 ω

Engine codes AHU 1Z:

• ‒ → Measure resistance between connector contacts 1 + 2 and 2 + 3.
      Specification: 5 ... 7 ω

If the specification is not obtained:

• ‒ Replace injection pump => Page 23-19.

If the specification is obtained:

• ‒ Remove dash panel insert:

=> Electrical system; Repair group 90; dash panel insert; removing and installing dash panel insert

• ‒ → Connect test box V.A.G 1598/18 to control unit wiring loom.

Engine codes AFN, AVG:

• ‒ → Check wiring between test box and connector for open circuit according to current flow diagram.
      Contact 1+ socket 29
      Contact 2+ socket 7
      Contact 3+ socket 52
      Wire resistance: max. 1.5 ω
• ‒ Additionally check wires for short to one another, to vehicle earth and to battery positive.
      Specification: ∞ω

Engine codes AHU 1Z:

• ‒ → Check wiring between test box and connector for open circuit according to current flow diagram.
      Contact 1+ socket 29
      Contact 2+ socket 7
      Contact 3+ socket 52
      Wire resistance: max. 1.5 ω
• ‒ Additionally check wires for short to one another, to vehicle earth and to battery positive.
      Specification: ∞ω

If no wiring fault is detected:

• ‒ Renew Diesel direct injection system control unit (J248) => Page 23-5, item 9.

Checking quantity adjuster (N146)

• ‒ Press the ⇒key.
• ‒ Press keys 0 and 6 for the "End data transfer" function and confirm input with the Q key.
• ‒ Switch off ignition.

• ‒ Disconnect connector =>Fitting locations overview, Page 23-4.

Engine codes AFN, AVG:

• ‒ → Measure resistance between connector contacts 5+6.
      Specification: 0.5...2.5 ω

Engine codes AHU 1Z:

• ‒ → Measure resistance between connector contacts 5+6.
      Specification: 0.5...2.5 ω

If the specification is not obtained:

• ‒ Replace injection pump => Page 23-19.

If the specification is obtained:

• ‒ Remove dash panel insert:

=> Electrical system; Repair group 90; dash panel insert; removing and installing dash panel insert

• ‒ → Connect test box V.A.G 1598/18 to control unit wiring loom.

Engine codes AFN, AVG:

• ‒ → Check wiring between test box and connector for open circuit according to current flow diagram.
      Contact 5+ sockets 23, 45 and 68
      Contact 6+ sockets 4, 5 and 49
      Wire resistance: max. 1.5 ω
• ‒ Additionally check wires for short to one another, to vehicle earth and to battery positive.
      Specification: ∞ω

Engine codes AHU 1Z:

• ‒ → Check wiring between test box and connector for open circuit according to current flow diagram.
      Contact 5+ sockets 23, 45 and 68
      Contact 6+ sockets 4, 5 and 49
      Wire resistance: max. 1.5 ω
• ‒ Additionally check wires for short to one another, to vehicle earth and to battery positive.
      Specification: ∞ω

If no wiring fault is detected:

• ‒ Renew Diesel direct injection system control unit (J248) => Page 23-5, item 9.