SEAT Workshop Service and Repair Manuals

Special tools, workshop equipment, testers, measuring instruments and auxiliary items required

• ◆ Fault reader V.A.G 1551 or vehicle system tester V.A.G 1552 with cable V.A.G 1551/3
• ◆ Test box V.A.G 1598/22
• ◆ Hand multimeter V.A.G 1526 or multimeter V.A.G 1715
• ◆ Adapter set V.A.G 1594
• ◆ Current flow diagram

Check conditions

• ● Coolant temperature at least 85 °C.
• ● Exhaust system between catalyst and cylinder head must be free of leaks

Functional check

• ‒ Connect fault reader V.A.G 1551 (V.A.G 1552). Start engine and select "Address word" 01 of engine control unit. When doing this the engine must be running at idling speed.
  (Connecting fault reader and selecting engine control unit .)

• ‒ Press keys 0 and 8 for the function "Read measured value block" and confirm entry with Q key.

• ‒ Press keys 0, 0 and 3 for "Display group number 3" and confirm entry with Q key.

• ‒ Check whether the coolant temperature is above 85 °C in display zone 3.
• ‒ Change to display group 9 as follows:
• ‒ Press C key.

• ‒ Press keys 0, 0 and 9 for "Display group number 9" and confirm entry with Q key.

• ‒ Note Lambda probe voltage in display zone 3. The voltage must
      fluctuate at least 30 times per minute
  in range of
      0... 1.0 V.
• ‒ Press ⇒key.
• ‒ Press keys 0 and 6 for the "End data transfer" function and confirm input with the Q key.

If the Lambda regulation does not fluctuate as stated:

• ‒ Carry out road test and burn Lambda probes clean and repeat check.

If the specifications are not obtained again:

• ‒ Check Lambda probe heating => Page 24-22.
• ‒ Evaluate the measured value blocks 7 to 9
  => Page 01-77, Evaluating measured value blocks, display groups 0...13.

If the voltage change is slower, determine cause of fault. => Page 24-90.

If the displayed figure remains constant:

• ‒ Continue check according to following table.

Possible causes of fault if probe control frequency is too slow:

• ◆ The slots or holes in probe body are blocked
• ◆ The probe vent hole in area of connecting wire is blocked
• ◆ The probe has been overheated (glazed)
• ◆ The probe has been damaged by leaded fuel

Checking basic voltage

• ‒ → Separate 4 pin connector (left on vehicle underbody) to Lambda probe (G39) -arrow-.

• ‒ → Connect multimeter with aux. cables from V.A.G 1594 to measure voltage at contacts 3+4 (connector to engine control unit).
• ‒ Switch on ignition and measure basic voltage.
      Specification: 0.40...0.50 V
• ‒ Switch off ignition.

If the specification is not obtained:

• ‒ Check Lambda probe wiring
  => Page 24-92

If the specification is attained:

• ‒ Replace Lambda probe (G39).

Checking Lambda probe wiring

• ‒ → Connect test box V.A.G 1598/22 to control unit wiring harness.

• ‒ → Check wiring between test box and 4 pin connector (to control unit) for open circuit according to current flow diagram.
      Contact 3+socket 25
      Contact 4+socket 26
      Wire resistance: Max. 1.5 ω
• ‒ Check wiring at connector contacts 3+4 for short circuit to contacts 1+2 using current flow diagram.
      Specification: ∞ω

If no wiring fault is detected:

• ‒ Replace Lambda probe (G39).