Skoda Workshop Service and Repair Manuals

Tightening torques

Gearbox ? 09.00 to 1.4/55 kW and 1.4/74 kW engine

Position	Screw	Qty	Nm
1	M12 x 65	1	80
21)	M12 x 140	2	80
3	M12 x 65	1	80
42)	M10 x 50	2	40
5	M12 x 80	1	80
A	Dowel sleeves for centering	2

1) Screw with threaded pin M8.

2) only for 1.4 ltr/55 kW engine screws M10 x 35 (cover plate for flywheel)

Gearbox 10.00 ? to 1.4/55 kW and 1.4/74 kW engine

Position	Screw	Qty	Nm
1	M12 x 65	1	80
21)	M12 x 140	2	80
3	M12 x 65	1	80
4	M10 x 50	2	40
5	M12 x 80	1	80
A	Dowel sleeves for centering	2

1) Screw with threaded pin M8.

Gearbox to 1.9/47 kW and 2.0/85 kW engine

Position	Screw	Qty	Nm
1	M12 x 55	2	80
21)	M12 x 140	2	80
3	M10 x 50	3	40
4	M12 x 65	1	80
A	Dowel sleeves for centering	2

1) Screw with threaded pin M8.

Gearbox on 1,4/51 kW Engine

Position	Screw	Qty	Nm
1	M12 x 70	2	80
21)	M12 x 150	1	80
31)	M12 x 150	1	80
41)	M10 x 70	1	40
5	M10 x 70	1	40
6	M12 x 80	1	80
72)	M6 x 8	1	10
A	Dowel sleeves for centering	2

1) Screw with threaded pin M8.

2) Attachment of cover plate for flywheel

Gearbox to 1.2/40 kW and 1.2/47 kW engine

Position	Screw	Qty	Nm
1	M12 x 65	3	80
21)	M12 x 140	2	80
3	M12 x 80	1	80
4	M10 x 60	2	40
A	Dowel sleeves for centering	2

Pendulum support to gearbox -screws 1- and assembly carrier -screw 2-   Note Position the screws -1- in the elongated holes of the pendulum support in such a way that there is maximum distance between the gearbox and the assembly carrier.

Tightening torques

Component	Nm
small cover plate (behind right flange shaft) for flywheel	10
Gearbox mounting bracket to gearbox 1) M10	→ Engine → Rep. Gr.10
Gearbox mounting bracket to gearbox mount1) M10	→ Engine → Rep. Gr.10
Cable support to gearbox up to 05.06	→ Chapter
Cable support to gearbox as of 06.06	→ Chapter
Gearbox shift lever to gearshift shaft up to 05.06	→ Chapter
Gearbox shift lever to gearshift shaft as of 06.06	→ Chapter
Slave cylinder to gearbox	→ Chapter
Pendulum support1)	→ Engine → Rep. Gr.10
Nut for attaching double clamp of exhaust system	→ Engine → Rep. Gr.10
Steering joint to front track control arm1) M8	→ Chassis → Rep. Gr.40
Coupling rod to anti-roll bar	→ Chassis → Rep. Gr.40
Drive shaft to flange shaft	→ Chassis → Rep. Gr.40
Protective cap for drive shaft on engine	→ Chassis → Rep. Gr.40
Wheel bolts to wheel hub	→ Chassis → Rep. Gr.44

1) Always replace these screws → Electronic Catalogue of Original Parts.