Fabia Mk2
| lI - Summary of components assembly carrier, track control arm, anti-roll bar, coupling rod, bracket, pendulum support (as of CW 12 2008) |
Note| t | An assembly carrier with consoles forming a unit (welded piece) is installed on vehicles manufactured as of CW 12 2008. Additionally the bottom track control arm, steering joint, wheel bearing housing were changed. |
| t | An assembly carrier with consoles mounted was inserted on vehicles up to CW 11 2008 → Chapter. |
| t | Welding and straightening work is not allowed on the bearing and wheel control components of the wheel suspension. |
| t | Always replace the self-locking nuts and screws. |
| t | Always replace corroded self-locking nuts and screws. |
| t | All screws must always be tightened firmly in the unladen condition (unladen weight position) to the chassis parts with rubber-metal bearings - do not load the vehicle → Chapter. |
| 1 - | Assembly carrier |
| q | removing and installing → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 2 - | Screw, 20 Nm + 90° |
| q | Screws for anti-roll bar clamps |
| q | replace after each removal |
| 3 - | Nut, 40 Nm |
| q | Assignment → Electronic Catalogue of Original Parts |
| 4 - | Anti-roll bar |
| q | to remove and install lower assembly carrier |
| q | removing and installing → Chapter |
| q | Assignment → Electronic Catalogue of Original Parts |
| 5 - | Rubber bearing |
| q | Assignment → Electronic Catalogue of Original Parts |
| 6 - | Spring strap clamp |
| q | Assignment → Electronic Catalogue of Original Parts |
| 7 - | Nut, 40 Nm |
| q | Assignment → Electronic Catalogue of Original Parts |
| 8 - | Coupling rod |
| q | Assignment → Electronic Catalogue of Original Parts |
| 9 - | Bracket |
| 10 - | Nut |
| q | replace after each removal |
| 11 - | Rubber-metal bearing |
| q | Rear rubber-metal bearing for track control arm |
| q | replace → Chapter |
| 12 - | Screw, 20 Nm + 90° |
| q | replace after each removal |
| 13 - | Screw, 70 Nm + 90° |
| q | replace after each removal |
| 14 - | Self-locking nut, 20 Nm + 90° |
| q | replace after each removal |
| 15 - | Steering joint |
| q | check → Chapter |
| q | removing and installing → Chapter |
| 16 - | Self-locking nut, 40 Nm + 45° |
| q | replace after each removal |
| 17 - | Screw, 70 Nm + 90° |
| q | replace after each removal |
| 18 - | Clip |
| q | Assignment → Electronic Catalogue of Original Parts |
| 19 - | Air deflector |
| q | Assignment → Electronic Catalogue of Original Parts |
| 20 - | Screw, 70 Nm + 90° |
| q | replace after each removal |
| 21 - | track control arm |
| q | removing and installing → Chapter |
| 22 - | Screw, 70 Nm + 90° |
| q | replace after each removal |
| 23 - | Screw, 30 Nm + 90° |
| q | replace after each removal |
| q | Position the screws in the elongated holes of the pendulum support in such a way that there is maximum distance between the gearbox and the assembly carrier |
| 24 - | Dowel screw, 40 Nm + 90° |
| q | replace after each removal |
| 25 - | Rubber-metal bearing |
| q | Front rubber-metal bearing for track control arm |
| q | replace → Chapter |
| 26 - | Pendulum support |
| q | do not disassemble |
| q | Position the screws in the elongated holes of the pendulum support in such a way that there is maximum distance between the gearbox and the assembly carrier |
| q | Assignment → Electronic Catalogue of Original Parts |
